Page 1 TOSHIBA TECRA M1 Portable Personal Computer User’s Manual Get other manuals https://www.bkmanuals.com...
Page 2 © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.
Page 3 WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripher- als or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port,...
Page 4 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: PT930* conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...
Page 5 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 6 Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made.
Page 7 FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 8 Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other...
Page 9 NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termina- tion on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Page 10 Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
Page 11 ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) ❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers.
Page 12 General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.
Page 13 Description on Laser specification The optical drive such as CD-ROM drive, DVD-ROM drive, DVD/CD-RW drive and DVD Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE...
Page 14 Get other manuals https://www.bkmanuals.com...
Page 15: Table Of Contents
Table of Contents Preface Manual contents ................xxiii Conventions ..................xxiv Abbreviations ..................xxiv Icons ....................xxiv Keys ....................xxiv Key operation ..................xxv Display ....................xxv Messages ..................xxv General Precautions Stress injury ................... xxvii Heat injury ..................xxvii Pressure or impact damage ............
Page 16 Standby mode .................. 3-10 Restarting the computer ..............3-12 Restoring the preinstalled software from the Product Recovery CD-ROM ..............3-13 Chapter 4 Operating Basics TOSHIBA Dual Pointing Device ............4-1 Using the Touch Pad ................4-1 Get other manuals https://www.bkmanuals.com...
Page 17 Using the AccuPoint ................4-2 AccuPoint precautions ............... 4-2 Replacing the cap ................4-2 Using the USB diskette drive ............4-3 Connecting 3 1/2" diskette drive ............4-4 Disconnecting 3 1/2" diskette drive ............. 4-4 Changing Slim Select Bay modules ..........4-5 Removing a module ................
Page 18 Disconnecting LAN cable ..............4-28 Cleaning the computer ..............4-28 Moving the computer ..............4-28 Heat dispersal .................. 4-29 Chapter 5 The Keyboard Typewriter keys ................. 5-1 F1 … F12 function keys ..............5-2 Soft keys: Fn key combinations ............5-2 Emulating keys on enhanced keyboard ..........
Page 19 TOSHIBA Password Utility .............. 6-16 User password ................. 6-16 Supervisor password ................. 6-17 Starting the computer by password ..........6-18 Power-up modes ................6-18 Windows utilities ................6-19 Hot keys ................... 6-19 Panel power off ................6-19 System Auto Off ................6-19 Chapter 7 HW Setup HW Setup ...................
Page 20 Using the TOSHIBA Console button ..........8-21 Changing the resolution ..............8-21 i.LINK (IEEE1394) ................8-22 Precautions ..................8-22 Connecting ..................8-22 Disconnecting ................... 8-23 Advanced Port Replicator II ............8-23 Parallel printer ................8-24 Security lock ..................8-25 Chapter 9 Troubleshooting Problem solving process ..............
Page 21 Bluetooth ..................9-24 Real Time Clock ................9-24 TOSHIBA support ................9-25 Before you call ................. 9-25 Where to write .................. 9-25 Appendixes Appendix A Specifications ................... A-1 Appendix B Display Controller and Modes ............B-1 Appendix C AT Commands .................. C-1 Appendix D S-registers ..................
Page 22 xxii Get other manuals https://www.bkmanuals.com...
Page 23: Preface
Chapter 4, Operating Basics, includes instructions on using the following devices: TOSHIBA Dual Pointing Device, Slim Select Bay modules, USB diskette drive, optical media drives, microphone, modem, Wireless communication features, LAN.
Page 24: Conventions
User's Manual Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup explains how to configure the computer using the HW Setup program. Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, suggests courses of action if the computer doesn’t seem to be working properly.
Page 25: Key Operation
Conventions Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Page 26 User's Manual xxvi Get other manuals https://www.bkmanuals.com...
Page 27: General Precautions
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 28: Cpu Performance Disclaimer
For optimum performance, use your computer product only under recommended conditions Read additional restrictions under “Environmental Conditions” in the Appendix A of the Online Manual. Contact TOSHIBA Technical Service and Support for more information. PC card overheating Some PC cards can become hot with prolonged use.
Page 29: Chapter 1 Introduction
CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not prein- stalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 30: Windows 2000 Service Pack 3
• Wireless LAN driver • Bluetooth driver • Sound Driver for Windows • DVD Video Player • LAN Drivers • Infrared Device Driver • TOSHIBA Dual Pointing Device utility • TOSHIBA Power Saver • TOSHIBA Console • Online manual ❑ Documentation: •...
Page 31: Features
If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple- mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer...
Page 32 User's Manual AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage from 100 to 240 volts;...
Page 33 Features CD-RW/DVD-ROM Some models are equipped with a full-size, CD-RW/DVD- drive ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 8 speed and CD-RW at up to 8 speed.
Page 34 See Chapter 5, Keyboard, for details. TOSHIBA Dual Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows. Built-in AccuPoint This pointer control stick, located in the center of the keybord, provides convenient control of the cursor.
Page 35 Features Slots PC card The PC card slot accommodates two 5 mm Type II cards or one Type III card. SD card This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory.
Page 36 Slim Select Bay is a single-drive bay that accommodates a CD-ROM drive, DVD-ROM drive, CD-RW/DVD-ROM drive, DVD Multi drive, secondary hard disk drive or secondary battery. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system.
Page 37: Special Features
Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Console Press this button to launch an application automatically.
Page 38 You can specify the time and select either System Standby or System Hibernate in the System standby and System hibernate item of the Power Save Mode window in TOSHIBA Power Saver. Keypad overlay A ten-key pad is integrated into the keyboard.
Page 39: Utilities
This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or read.me files. TOSHIBA Power Saver To access this power savings management program, open the Control Panel and select the TOSHIBA Power Saver icon.
Page 40 You can boot ConfigFree from the menu bar as follows. Windows 2000: [Start] - [Programs] - [TOSHIBA ConfigFree] - [ConfigFree] Windows XP: [Start] - [All Programs] - [TOSHIBA ConfigFree] - [ConfigFree] TOSHIBA Dual This utility has the following functions: Pointing Device utility To disable/enable TOSHIBA Dual Pointing Device with Fn + F9 keys.To customize the functions of TOSHIBA...
Page 41: Options
TOSHIBA Brightness Sensor Control. In order to use TOSHIBA Brightness Sensor Control, you have to set Brightness Sensor in TOSHIBA Power Saver to ON. Options You can add a number of options to make your computer even more powerful and convenient to use.
Page 42 User's Manual Security plate This device covers the bottom of the computer when it is connected to a Advanced Port Replicator II to prevent removal of components. Wireless LAN Kit This option enbles wireless LAN functions in computers that do not have wireless preinstalled. It is installed by dealers only.
Page 43: Chapter 2 The Grand Tour
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. NFRARED ICROPHONE EADPHONE...
Page 44: Left Side
User's Manual Headphone jack This jack lets you connect digital speakers or stereo headphones (16 ohm minimum). When you connect digital speakers or headphones, the internal speaker is automati- cally disabled. Volume control Use this dial to adjust the volume of the stereo speakers and subwoofer or the stereo headphones.
Page 45 Left side PC card slot A PC card slot can accommodate two 5 mm Type IIcards or one Type III card. You can install any industry standard PC card such as a SCSI adaptor, Ethernet adaptor or flash memory card. CAUTION: Keep foreign objects out of the PC card slot.
Page 46: Right Side
User's Manual Right side Figure 2-3 shows the computer’s right side. PORT ELECT Figure 2-3 The right side of the computer Universal A third Universal Serial Bus (USB 2.0 compliant) port is on Serial Bus the right side. See Universal Serial Ports in the Left side (USB 2.0) port section for details.
Page 47 Back side External monitor This 15-pin port lets you connect an external video port display. Serial port Use this 9-pin port to connect external serial devices such as an external modem, a serial mouse or printer. Parallel port This Centronics-compatible, 25-pin parallel port is used to connect a parallel printer or other parallel device.
Page 48: Underside
User's Manual i.LINK (IEEE1394) Connect an external device, such as a digital video camera port to this port for high-speed data transfer. Cooling vents Cooling vents help CPU keep from overheating. CAUTION: Do not to block the cooling vents. Also do not to keep foreign objects out of them.
Page 49 Under side Slim Select Bay See the Right side section in this chapter for details. Slim Select Bay Slide the lock to release or secure the Slim Select Bay lock ejector. CAUTION: Be sure to lock the Slim Select Bay lock before you transport or carry the computer.
Page 50: Front With The Display Open
User's Manual Front with the display open This section shows the computer with the display open. Refer to the appropriate illustration for details. ISPLAY HINGE ISPLAY SCREEN TOSHIBA C ONSOLE BUTTON LCD S ENSOR SWITCH NOT SHOWN TOSHIBA P RESENTATION...
Page 51 LCD and CRT. You can also return to single display by pressing this button twice. The setting of TOSHIBA Presentation button can be changed through the property of TOSHIBA Console. Display mode is changed to the multi-monitor display by selecting "Different Image"...
Page 52 TOSHIBA Brightness Sensor Control. If the compensated brightness still does not fit to the condition to use, adjust the brightness manually using Fn + F6/7 keys with TOSHIBA Power Saver set to OFF. Refer to Chapter 5 for details. LCD Sensor switch This switch senses when the LCD panel is closed or opened and activates the Panel Power Off/On feature.
Page 53: System Indicators
System indicators System indicators LEDs beneath icons, light when various computer operations are in progress. DC IN 15V OWER ATTERY ELECT IRELESS COMMNICATION Figure 2-7 System indicators DC IN 15V The DC IN 15V indicator glows in green when DC power is supplied from the AC power adaptor.
Page 54: Keyboard Indicators
User's Manual Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers. UMERIC MODE INDICATOR RROW MODE...
Page 55: Usb Diskette Drive
USB diskette drive Numeric mode You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard. USB diskette drive A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port.
Page 56: Slim Select Bay Modules
User's Manual Slim Select Bay modules The Slim Select Bay can accommodate the following modules: CD-ROM drive, DVD- ROM drive, CD-RW/DVD-ROM drive, DVD Multi drive, optional secondary battery pack and optional Slim Select Bay HDD adaptor. CD-ROM drive An optional full-size, maximum 24-speed CD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") compact discs without using an adaptor.
Page 57: Dvd-Rom Drive
Slim Select Bay modules CAUTION: Check the Slim Select Bay indicator when you use the CD-ROM drive. Do not press the eject button, disconnect a drive or turn off the computer while the light is glowing. Doing so could damage the CD or the drive.
Page 58: Cd-Rw/Dvd-Rom Drive
User's Manual Eject button Press the eject button to open the drawer partially. Eject hole Insert a slender object to open the drawer when the power to the computer is off. CD/DVD-In-Use This indicator lights when the CD/DVD is being Indicator accessed.
Page 59 Slim Select Bay modules CD/DVD-I INDICATOR JECT HOLE JECT BUTTON Figure 2-13 The CD-RW/DVD-ROM drive This drive supports the following formats: • DVD ROM • DVD Video • CD-ROM • CD-EXTRA • Photo CD • Audio CD • CD-ROMxA • CD-DA •...
Page 60: Dvd Multi Drive
User's Manual Russia, Indian Subcontinent, Africa, North Korea, Mongolia China CD-R describes compact discs that can be written only once. The recorded data cannot be erased or changed. Use 8-speed CD-R discs. CD-RW describes compact discs that can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4- to 10-speed discs.
Page 61 Slim Select Bay modules CD/DVD-I INDICATOR JECT HOLE JECT BUTTON Figure 2-14 The DVD Multi drive CD/DVD-In-Use This indicator lights when a CD/DVD is being accessed. Indicator Eject button Press the eject button to open the drawer partially. Eject hole Insert a slender object to open the drawer when the power to the DVD Multi drives is off.
Page 62: Secondary Battery Pack
User's Manual NOTE: Use the WinDVD 4 application to view DVD-Video discs. CD-R and DVD-R discs can be written only once. The recorded data cannot be erased or changed. CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed CD- RW discs or high-speed 4- to 10-speed discs.
Page 63: Weight Saver Module
Slim Select Bay modules To install an HDD, follow the steps below. 1. Slide the cover lock to the unlock position and lift up the cover. 2. Lay the HDD into the Slim Select Bay HDD adaptor and push it forward to secure the connectors.
Page 64: Ac Adaptor
CAUTION: Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. WARNING: Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fine or rupture.
Page 65: Chapter 3 Getting Started
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 66: General Conditions
User's Manual General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation. ❑...
Page 67: Seating And Posture
Setting up your work space Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. ELOW EYE LEVEL ANGLES OOT REST...
Page 68: Lighting
User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.
Page 69: Connecting The Ac Adaptor
1) Use only the AC adaptor supplied with your computer or an equivalant adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.
Page 70: Opening The Display
User's Manual 2. Connect the AC adaptor’s DC output plug to the DC IN 15V input port on the back of the computer. Figure 3-3 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN 15V indicators on the front of the computer should glow.
Page 71: Turning On The Power
Turning on the power Turning on the power This section describes how to turn on the power. NOTE: After you turn on the power for the first time, do not turn it off until you have set up the operating system. 1.
Page 72: Hibernation Mode
User's Manual 2. Make sure all disk activity has stopped, then remove the CD/DVD-ROM or diskette. CAUTION: Make sure the Disk, Slim Select Bay and Slim Select Bay’s module indicators are off. If you turn off the power while a disk is being accessed, you can lose data or damage the disk.
Page 73 Turning off the power NOTE: For the computer to shut down in hibernation mode, the hiberna- tion feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.
Page 74: Standby Mode
Standby, it might not be restored when the computer wakes up from standby. To prevent the computer from automatically entering standby mode, disable Standby in TOSHIBA Power Saver. Open the Standby setting. That action, however, will nullify the computer's Energy Star compliance.
Page 75 In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. b. In Windows 2000, double-click the TOSHIBA Power Saver icon. 3. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility discribed in the Control Panel.
Page 76: Restarting The Computer
User's Manual When you turn the power back on, you can continue where you left when you shut down the computer. NOTES: 1. When the computer is shut down in standby mode, the power indicator flashes orange. 2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode.
Page 77: Restoring The Preinstalled Software From The Product Recovery Cd-Rom
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
Page 78 User's Manual 3-14 Get other manuals https://www.bkmanuals.com...
Page 79: Chapter 4 Operating Basics
Chapter 4 Operating Basics This chapter gives information on basic operations including using the TOSHIBA Dual Pointing Devices, USB diskette drive, the microphone, the internal modem, wireless communication, LAN, and changing Slim Select Bay modules. It also provides tips on caring for your computer, diskettes and CD/DVDs.
Page 80: Using The Accupoint
User's Manual Click: Tap the Touch Pad once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the AccuPoint To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer.
Page 81: Using The Usb Diskette Drive
Using the USB diskette drive 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight up. Figure 4-2 Removing the AccuPoint cap 2. Position a new cap on the peg and press it into place. NOTE: The peg is square, so be careful to align the cap’s square hole with the peg.
Page 82: Connecting 3 1/2" Diskette Drive
User's Manual Connecting 3 1/2" diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to Figure 4-3. CAUTION: Make sure the connector is right side up and properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.
Page 83: Changing Slim Select Bay Modules
Select Bay slot. 2. Before removing or inserting a second battery pack, turn off the computer’s power. NOTE: The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction information on using this utility to change modules while the computer’s power is on.
Page 84: Inserting A Module
User's Manual ELECT ELECT LOCK MODULE Figure 4-4 Removing the DVD-ROM drive Inserting a module Insert the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks.
Page 85: Using Optical Media Drives
Using optical media drives Using optical media drives The text and illustrations in this section refer primarily to the Fixed DVD-ROM drive. However, operation is the same for other optical drive in the Slim Select Bay. The full-size drive provides high-performance execution of CD/DVD-ROM-based programs.
Page 86 User's Manual b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Page 87 Using optical media drives 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-9 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray.
Page 88: Removing Discs
User's Manual 5. Push the center of the drawer to close it. Press gently until it locks into place. CAUTION: If the CD/DVD is not seated properly when the drawer is closed, the CD/DVD might be damaged. Also, the drawer might not open fully when you press the eject button.
Page 89: Writing Cds On Cd-Rw/Dvd-Rom Drive
Writing CDs on CD-RW/DVD-ROM drive 2. The CD/DVD extends slightly over the sides of the drawer so you can hold it. Hold the CD/DVD gently and lift it out. Figure 4-11 Removing a CD/DVD 3. Push the center of the drawer to close it. Press gently until it locks into place. Writing CDs on CD-RW/DVD-ROM drive Depending on the type of drive installed, you may be able to write CDs.
Page 90: When Writing Or Rewriting
User's Manual CD-RW: MITUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ❑ CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.
Page 91: Writing Cd/Dvds On Dvd Multi Drive
DVD Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: ❑ Damage to any CD-R/-RW or DVD-R/-RW/-RAM disc that may be caused by writing or rewriting with this product.
Page 92: Read/Write Function Chart
User's Manual Read/write function chart Disc type CD-R CD-RW DVD-R DVD-RW DVD-RAM DVD+R DVD+RW Read Write Drag’n Drop CD*1 DVDfunSTUDIO*1 DVD-MovieAlbum*1 DVD-Video*2 DVD VR*2 (DVD VideoRecoding) *1 Software supplied with the product can be used for writing to a disc. *2 Video format can be written.
Page 93 Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/-RW and DVD-R/-RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 94: Before Writing Or Rewriting
User's Manual ❑ Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part. ❑ Data deleted (erase) from a CD-RW and DVD-RW/-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.
Page 95: When Writing Or Rewriting
Writing CD/DVDs on DVD Multi drive ❑ Writing with software other than Drag'n Drop CD, DVDfunSTUDIO and DVDMovieAlbum is not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/-RW or DVD-R/-RW/-RAM disc. ❑...
Page 96: Data Verification
User's Manual ❑ Do not use the DISC Backup function of Drag'n Drop CD to copy DVD-Video and DVD-ROM with copyright protection, because the copy will not play correctly. ❑ DVD-RAM disc cannot be backed up with the DISC Backup function of Drag'n Drop CD.
Page 97 Writing CD/DVDs on DVD Multi drive ❑ When Drag'n Drop or similar software is resident in the computer's memory, the DVD Multi drive locks. In this situation, other software cannot be used to write data to the disc. ❑ While you are editing DVD-R/-RW/-RAM, you can display previews. However, if an application other than WinDVD is running, the preview might not display properly.
Page 98: Media Care
User's Manual Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
Page 99: Using The Microphone
Using the microphone Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speaker, “howling” may be heard under certain conditions.
Page 100: Properties Menu
User's Manual 1. a. In Windows XP, click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. NOTE: Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. If you change the Country/Region in the Control Panel, the change may not take effect.
Page 101: Connecting
Modem Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match. A warning dialog box is displayed if current settings for region code and telephony location are incorrect.
Page 102: Disconnecting
User's Manual CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as an optical drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1.
Page 103: Security
TOSHIBA strongly recommend the customer to enable the WEP function. 2. TOSHIBA is not liable for the eavesdropping of data due to the use of wireless LAN and the damage thereof.
Page 104: Wireless Communication Switch
W-LAN. Open or click the following: start, Control Panel, System, Hardware Device Manager, Network adapters, TOSHIBA Wireless LAN Mini PCI Card or Atheros AR5001X Mini PCI Wireless Network Adaptor and enable. The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-Tx) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).
Page 105: Connecting Lan Cable
Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T), be sure to connect with a CAT5 cable or a CAT5E cable.
Page 106: Disconnecting Lan Cable
User's Manual Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. CAUTION: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector.
Page 107: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Power Save Mode window in TOSHIBA Power Saver. Maximum...
Page 108 User's Manual 4-30 Get other manuals https://www.bkmanuals.com...
Page 109: Chapter 5 The Keyboard
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s key- board layout your computer is configured with.
Page 110: Soft Keys: Fn Key Combinations
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 111 Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard.
Page 112: Hot Keys
Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the Plugged in or Running on batteries item of the Power Saver Properties window in TOSHIBA Power Saver. Get other manuals https://www.bkmanuals.com...
Page 113 When you press these hot keys, the current setting will be displayed for two seconds by an icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in TOSHIBA Power Saver. Get other manuals https://www.bkmanuals.com...
Page 114 You can also change this setting through the Monitor brightness item of the Power Save Mode window in TOSHIBA Power Saver. NOTES: 1. The brightness level is always set at the maximum value for about 18 seconds, when the LCD turns on.
Page 115: Fn Sticky Key
1024X768, from 1024X768 to 800X600, from 800X600 to the original resolution. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA Utilities and click Accessibility.
Page 116: Turning On The Overlays
User's Manual Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode F10 indicator lights. Now try cursor and page control using the keys shown in figure 5-2.
Page 117: Temporarily Using Normal Keyboard (Overlay On)
Generating ASCII characters Temporarily using normal keyboard (overlay While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.
Page 118 User's Manual With the overlay off: 1. Hold down Alt + Fn. 2. Using the overlay keys, type the ASCII code. 3. Release Alt + Fn, and the ASCII character appears on the display screen. 5-10 Get other manuals https://www.bkmanuals.com...
Page 119: Chapter 6 Power And Power-Up Modes
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 120 User's Manual Table 6-1 Power conditions continued Power on Power off (no operation) 2nd battery • Operates •No charge adaptor fully • No charge •LED: 2nd battery green connected charged • LED: 2nd battery green DC IN green DC IN green 2nd battery •...
Page 121 When the main battery is not charging For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a secondry battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
Page 122: Power Indicators
User's Manual Power indicators As shown in the above table, the Battery, Slim Select Bay, DC IN 15V and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the secondary battery.
Page 123: Battery Types
Dispose of the battery as required by local ordinances or regulations. Use only batteries recom- mended by TOSHIBA as replacements. 2. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.
Page 124: Secondary Battery (Option)
Press [F1] key to set Date/Time. CAUTION: The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Page 125: Care And Use Of The Battery Pack
Care and use of the battery pack Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack.
Page 126 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture.
Page 127 Care and use of the battery pack 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.
Page 128: Charging The Batteries
Hibernation mode (so you don’t lose data) and automatically turns off. NOTE: The computer enters Hibernation mode only if Hibernation is enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.
Page 129: Monitoring Battery Capacity
Care and use of the battery pack Battery charging notice The battery may not charge right away under the following conditions: ❑ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10°...
Page 130: Maximizing Battery Operating Time
How you configure the computer (for example, whether you enable battery- power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: • Processor speed •...
Page 131: Retaining Data With Power Off
Care and use of the battery pack Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (6600mAH) about 7 days (Standby mode) about 43 days (Boot mode) Battery pack (4400mAH) about 4 days (Standby mode)
Page 132: Replacing The Battery Pack
User's Manual Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator or Slim Select Bay indicator (if a Slim Select Bay 2nd battery pack is installed) flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.
Page 133: Installing The Battery Pack
RELEASE LATCH Figure 6-1 Releasing the battery pack CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery, follow the steps below.
Page 134: Toshiba Password Utility
User's Manual TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. NOTE: Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: Windows 2000 Start ->...
Page 135: Supervisor Password
SD card of any capacity, but it must be formatted correctly. If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format.To start the format tool, point to or click the following items: Windows 2000 Start ->...
Page 136: Starting The Computer By Password
User's Manual ❑ Create or invalidate a supervisor password token NOTE: This function in the Supervisor password utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ❑ Specify restrictions for general users. Starting the computer by password If you registered a password, there are two ways to start the computer: ❑...
Page 137: Windows Utilities
Panel power off Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation. See Chapter 5, Keyboard for details.
Page 138 User's Manual 6-20 Get other manuals https://www.bkmanuals.com...
Page 139: Chapter 7 Hw Setup
Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. HW Setup TOSHIBA HW Setup lets you configure settings for General, CPU, Boot Priority, Keyboard, LAN, Device Config, Parallel/Printer and Display. NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
Page 140 User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Setup This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings. About Click About to display the HW Setup version. This function lets you set the CPU operating mode.
Page 141 HW Setup HDD −> −> −> −> −> FDD −> −> −> −> CD-ROM −> −> −> −> −> LAN The computer looks for bootable files in −> the following order: HDD, diskette drive, CD-ROM* and LAN. (Default) −> −> −>...
Page 142 HW Setup. 4. Support of PCA (ATA) card boot is guaranteed only for TOSHIBA PC card HDDs. 5. A PCA (ATA) card takes the position of HDD in the Boot Priority Options list.
Page 143 HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key. (PS/2 keyboard only) No Fn key equivalent (Default) Disabled...
Page 144 User's Manual CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled. NOTE: The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature. Built-in LAN This feature enables or disables the Built-in LAN.
Page 145 HW Setup Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you set the display to be used when the computer is booted. Selects an external monitor if one is connected. Other- Auto-Selected wise, it selects the internal LCD.
Page 146 User's Manual Get other manuals https://www.bkmanuals.com...
Page 147: Chapter 8 Optional Devices
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ❑ PC cards ❑ SD cards ❑ Memory expansion Power devices ❑...
Page 148: Pc Cards
The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 149: Removing A Pc Card
PC cards After inserting the card, refer to the card’s documentation and check the configura- tion in Windows to make sure it is appropriate for your card. Removing a PC card To remove the PC card, follow the steps below. 1.
Page 150 User's Manual Locking the PC card slot To lock the PC card slot, follow the steps below. 1. When the computer is shipped, a screw secures the PC card lock in the unlocked position. Remove the screw. 2. Slide the PC card lock to the locked position. A metal tongue will cover the PC card slot.
Page 151: Sd Cards
SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.
Page 152: Inserting An Sd Card
User's Manual In order to run TOSHIBA SD memory card format, select [Start] - [All Programs] - [TOSHIBA SD card utilities] - [TOSHIBA SD memory card format], or right click the mouse on the icon of SD drive in Explore and select [TOSHIBA SD memory card format].
Page 153: Sd Card Care
SD cards 4. Pinch the card and remove it. CARD INDICATOR CARD Figure 8-6 Removing an SD card CAUTION: Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card.
Page 154: Memory Expansion
Avoid the mat that generates static electricity. CAUTION: Use only memory modules approved by TOSHIBA. CAUTION: Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module.
Page 155 Memory expansion 4. Turn the computer to the normal position and open the display panel. Tilt the display panel slightly beyond the upright position before removing the keyboard display. 5. Put your fingers on the both ends of the keyboard brace and remove it carefully to the direction indicated with arrows.
Page 156 User's Manual 7. Press the keyboard to the other side. Turn the keyboard upside down when a flat cable appears. CAUTION: Do not pull the keyboard when turning over. Otherwise the cable connecting the keyboard and the main body of computer will not return to the original position.
Page 157 Memory expansion 8. Raise the insulation sheet covering the memory module to appear the module. NSULATION SHEET Figure 8-11 Raising the insulation sheet 9. Keep the insulation sheet raised using adhesive tape. Figure 8-12 Raising the insulation sheet 8-11 Get other manuals https://www.bkmanuals.com...
Page 158 User's Manual 10. Insert a new module to the socket and push it downward to lie flat. Latches on either side will click into place to secure the module. Figure 8-13 Installing a memory module Figure 8-14 Installing two memory modules 11.
Page 159: Removing Memory Module
Memory expansion 12. Insert two tabs of the keyboard into the slits of the computer case and seat the keyboard at the original position. Refer to Figure 8-9 for tabs and slits. Fix it with three screws removed in 6. CAUTIONS: Be sure to use all screws that were removed in 6 and do not leave foreign matters such as adhesive tape used in 9 or screws removed and dropped in the computer.
Page 160: Hard Disk Drive Pack
User's Manual Figure 8-15 Removing the memory module 6. Follow the instructions 11 through 15 in “Installing memory module”. Hard disk drive pack An extra HDD expands the flexibility of your system and lets you carry your data without carrying the computer. NOTE: Use a point size 0 Phillips screwdriver.
Page 161 Hard disk drive pack Figure 8-16 Removing the HDD pack cover 7. Raise the HDD’s plastic tab, pinch it and slide the HDD pack to disconnect from the connector. CAUTION: Be sure to slide the HDD pack first and confirm that the HDD pack has disconnected.
Page 162: Installing The Hdd Pack
User's Manual Installing the HDD pack To install the hard disk drive, follow the steps below. 1. Place the HDD into the space for HDD. Slide the HDD to connect to the connector. 2. Fold over the plastic tab so that it goes into the HDD space. Press the HDD to ensure a firm connection.
Page 163: Installing
Slim Select Bay 2nd battery pack Installing To install the secondary battery pack in the adaptor, follow the steps below. 1. Fit the side of the secondary battery pack opposite the connector into the adaptor. 2. Lay the battery into the adaptor. The latch should close automatically to secure the secondary battery pack.
Page 164: Removing
User's Manual Removing To remove the secondary battery from the adaptor, follow the steps below. 1. Slide the latch in the direction of the arrow shown below. 2. Push the secondary battery pack up from the bottom and lift it out. Figure 8-20 Removing the secondary battery pack from the adaptor Additional AC adaptor If you frequently transport the computer between different sites such as your home...
Page 165 Slim Select Bay HDD adaptor 1. Slide the lock to the unlock position and open the lid. Figure 8-21 Opening the lid 2. Insert the HDD and push forward to ensure a firm connection. Figure 8-22 Inserting the HDD 8-19 Get other manuals https://www.bkmanuals.com...
Page 166: External Monitor
User's Manual 3. Close the lid and slide the lock to the lock position. Figure 8-23 Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer.
Page 167: Using The Toshiba Console Button
2. Connect the TV adaptor cable’s S Video plug to the S Video jack on the TV. 3. Press the TOSHIBA Console button. You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, Keyboard.
Page 168: I.link (Ieee1394)
Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data.
Page 169: Disconnecting
Advanced Port Replicator II 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ❑ You may need to install drivers for your i.LINK devices. ❑ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed.
Page 170: Parallel Printer
User's Manual The following ports and accessories are available on the Port Replicator. ❑ RJ45 LAN jack ❑ RJ11 Modem jack ❑ External monitor port ❑ Parallel port ❑ Serial port ❑ PS/2 mouse port ❑ PS/2 keyboard port ❑ DC IN socket ❑...
Page 171: Security Lock
Security lock 10. Set the mode to ECP and press OK. 11. Choose Reboot for the change to take effect. Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator II to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator.
Page 172 User's Manual 8-26 Get other manuals https://www.bkmanuals.com...
Page 173: Chapter 9 Troubleshooting
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 174: Analyzing The Problem
User's Manual ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.
Page 175: Hardware And System Checklist
Hardware and system checklist Hardware If you cannot find a software problem, check your hard- ware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals.
Page 176: Self Test
If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ❑...
Page 177 Hardware and system checklist Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally shut down. Problem Procedure Computer shuts down Leave the computer off until the computer and DC IN 15V indicator reaches room temperature, then turn it back on. blinks orange If the computer is still too warm, the DC IN 15V indicator will continue blinking when you turn on...
Page 178 If you do not think the battery is at the end of its operating life, see your dealer. Battery doesn’t Check the power consumption settings in power the computer TOSHIBA Power Saver Utility. Consider using a as long as expected power saving mode. Get other manuals https://www.bkmanuals.com...
Page 179: Password
Contact your dealer. or forgot password NOTE 1: For information on setting a password, refer to Chapter 6, Power and Power-Up Modes, starting the computer by Password, TOSHIBA Password Utility. NOTE 2: If you have made a token already, you can use it for authentication when the computer to enter password.
Page 180: Lcd Panel
User's Manual If you are still unable to use the keyboard, consult your dealer. LCD panel Problem Procedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
Page 181: Cd-Rom Drive
Hardware and system checklist There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk. Refer to your OS documentation or online HELP for information on running SCANDISK and the defragmenter.
Page 182: Dvd-Rom Drive
User's Manual Check your config.sys and autoexec.bat files to make sure they have the necessary drivers and execution lines. Some CDs The software or hardware configuration may run correctly, but be causing a problem. Make sure the others do not hardware configuration match’s your software’s needs.
Page 183: Cd-Rw/Dvd-Rom Drive
Hardware and system checklist Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs The software or hardware configuration may run correctly, but be causing a problem.
Page 184 User's Manual Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty.
Page 185: Dvd Multi Drive
Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording.
Page 186 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording.
Page 187: Diskette Drive
Hardware and system checklist Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not There may be a faulty cable connection. Check operate the connection to the computer and to the drive. You cannot access Try another diskette.
Page 188: Pc Card
User's Manual PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card Reseat the PC card to make sure it is error occurs firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation.
Page 189: Toshiba Dual Pointing Device
Then click the Detail Setting button and click the Device Select tab. Check that the Touch Pad is not selected. Pressing Fn + F9 to enables TOSHIBA Dual Pointing Device. On-screen pointer The system might be busy. If the pointer is...
Page 190 User's Manual 3. Set the double-click speed as instructed and click OK. If problems persist, contact your dealer. USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume mouse operation its normal shape and try again to move it.
Page 191: Usb
Hardware and system checklist Refer also to your USB device’s documentation. Problem Procedure USB device does Check for a firm cable connection between the not work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.
Page 192: Sound System
User's Manual Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Annoying sound You may be experiencing feedback.
Page 193: I.link (Ieee1394)
Hardware and system checklist Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. i.LINK (IEEE1394) Problem Procedure i.LINK device does Make sure the cable is securely connected to not function the computer and to the device.
Page 194 User's Manual You can also use the ATX command. Refer to the online help files for Appendix C, AT Commands. You place a call, Make sure the settings are correct in your but a connection communications application. can’t be made After making a call Make sure the tone or pulse selection in your you can’t hear a ring...
Page 195: Lan
Hardware and system checklist You can also use the ATS0 command. Refer to the online help files for Appendix D, S-registers. If problems persist, contact your dealer. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB.
Page 196: Bluetooth
User's Manual Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless communica- Bluetooth device tion switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on.
Page 197: Toshiba Support
TOSHIBA support TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 198 User's Manual United States of America United Kingdom TOSHIBA America Information TOSHIBA Information Systems (U.K.) Systems, Inc. Ltd. 9740 Irvine Boulevard TOSHIBA Court Irvine, California 92618 Weybridge Business Park Addlestone Road In Europe Weybridge, Surrey KT15 2UL Germany & Austria The Rest of Europe TOSHIBA Europe (I.E.) GmbH...
Page 199: Appendix A Specifications
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.6 kilograms, configured with: 14"XGA, 256MB RAM, 30GB HDD, DVD-ROM drive, modem, LAN, 6-cell battery 2.8 kilograms, configured with: 14"SXGA, 256MB RAM, 30GB HDD, CD-RW/DVD drive, modem, LAN, 9-cell battery Weight will vary with other configurations.
Page 200 User's Manual Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command...
Page 201 Appendix A Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) Get other manuals https://www.bkmanuals.com...
Page 202 User's Manual Get other manuals https://www.bkmanuals.com...
Page 203: Display Controller And Modes
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA), Super Extended Graphics Array (SXGA), Super Extended Graphics Array plus (SXGA+), support for the internal LCD and external monitors.
Page 204 User's Manual Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
Page 205 Appendix B Table1 Video modes (VGA) continued Video Type Resolution Character LCD Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 320 x 200 8 x 8 16 of 256K 16 of 256K Grph Pels 640 x 200 8 x 8 16 of 256K 16 of 256K Grph...
Page 206 User's Manual Table 2 Video modes (XGA) Resolution Vertical colors colors frequency (Hz) 640 x 480 256/256K 256/256K 800 x 600 256/256K 256/256K 1024 x 768 256/256K 256/256K 1280 x 1024 256/256K 256/256K (Virtual) 1600 x 1200 256/256K 256/256K (Virtual) 1920 x 1440 256/256K 256/256K...
Page 207 Appendix B Table 2 Video modes (XGA) continued Resolution Vertical colors colors frequency (Hz) 640 x 480 64K/64K 64K/64K 800 x 600 64K/64K 64K/64K 1024 x 768 64K/64K 64K/64K 1280 x 1024 64K/64K 64K/64K (Virtual) 1600 x 1200 64K/64K 64K/64K (Virtual) 1920 x 1440 64K/64K...
Page 208 User's Manual Table 2 Video modes (XGA) continued Resolution Vertical colors colors frequency (Hz) 640 x 480 16M/16M 16M/16M 800 x 600 16M/16M 16M/16M 1024 x 768 16M/16M 16M/16M 1280 x 1024 16M/16M 16M/16M (Virtual) 1600 x 1200 16M/16M 16M/16M (Virtual) 1920 x 1440 16M/16M...
Page 209 Appendix B Table 3 Video modes (Super XGA+) Resolution Vertical colors colors frequency (Hz) 640 x 480 256/256K 256/256K 800 x 600 256/256K 256/256K 1024 x 768 256/256K 256/256K 1280 x 1024 256/256K 256/256K 1400 x 1050 256/256K 256/256K 1600 x 1200 256/256K 256/256K (Virtual)
Page 210 User's Manual Table 3 Video modes (Super XGA+) continued Resolution Vertical colors colors frequency (Hz) 640 x 480 64K/64K 64K/64K 800 x 600 64K/64K 64K/64K 1024 x 768 64K/64K 64K/64K 1280 x 1024 64K/64K 64K/64K 1400 x 1050 64K/64K 64K/64K 1600 x 1200 64K/64K 64K/64K...
Page 211 Appendix B Table 3 Video modes (Super XGA+) continued Resolution Vertical colors colors frequency (Hz) 640 x 480 16M/16M 16M/16M 800 x 600 16M/16M 16M/16M 1024 x 768 16M/16M 16M/16M 1280 x 1024 16M/16M 16M/16M 1400 x 1050 16M/16M 16M/16M 1600 x 1200 16M/16M 16M/16M...
Page 212 User's Manual B-10 Get other manuals https://www.bkmanuals.com...
Page 213: At Commands
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 214 User's Manual Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default).
Page 215 Appendix C Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while...
Page 216 User's Manual Monitor speaker volume This command sets speaker volume to low, medium, or high. Low volume. Low volume. (Same as L0) Medium volume (default). High volume. Result Codes: n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode This command turns the speaker on or off. The speaker is off.
Page 217 Appendix C Result Codes: n=0,1 ERROR Otherwise On Return on-line to data mode Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). This command issues a retrain before returning to on-line data mode.
Page 218 User's Manual Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
Page 219 Appendix C Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT <RATE>, RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within...
Page 220 User's Manual &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: n=0,1 ERROR Otherwise &Dn DTR control This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal.
Page 221 Appendix C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.
Page 222 User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.
Page 223 Appendix C \Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. Buffer mode. No error control. Direct mode. MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures.
Page 224 User's Manual \Vn Protocol result code Disable protocol result code appended to DCE speed. Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 ERROR Otherwise % B View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed.
Page 225: Appendix D S-Registers
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
Page 226 User's Manual Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.
Page 227 Appendix D Response formatting character (user defined) This register determines the ASCII value used as the line feed charac- ter. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII...
Page 228 User's Manual Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (an- swer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction.
Page 229 Appendix D S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...
Page 230 User's Manual AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone ERROR...
Page 231 Appendix D Result Code Numeric Description DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
Page 232 User's Manual Get other manuals https://www.bkmanuals.com...
Page 233 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 234 User's Manual Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
Page 235 Appendix E * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
Page 236 User's Manual Get other manuals https://www.bkmanuals.com...
Page 237: Internal Modem Guide
Appendix F Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem NOTE: The internal modem is preinstalled.
Page 238 User's Manual Removing the internal modem To remove the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and any other peripheral device. 3. Turn the computer upside down and remove the battery pack. 4.
Page 239: Wireless Lan
Appendix G Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications Form Factor Mini PCI TypeIII Capability IEEE 802.11 Standard for Wireless LANS (DSSS) Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA) Network Microsoft Windows...
Page 240 Subject to the radio regulations that apply in your country/region, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region.
Page 241 Appendix G When installing Wireless LAN cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.
Page 242 User's Manual Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 5150-5850 MHz Note 5210 US only * US only * 5250 US only * 5290 US only * 5760 5800 US only * * Available Area: US (USA, CANADA) only A peer-to-peer mode is available under the following condition: A Wireless LAN card receives a “US county/region code”...
Page 243: Ac Power Cord And Connectors
Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size:...
Page 244 User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada United Kingdom UL approved BS approved CSA approved Australia Europe Approved by the AS approved appropriate agency Get other manuals https://www.bkmanuals.com...
Page 245: Parts Numbers
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules and communication devices. Get other manuals https://www.bkmanuals.com...
Page 246 User's Manual Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice.
Page 247: Glossary
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. IDE: integrated drive electronics Abbreviations I/O: input/output AC: alternating current IrDA: Infrared Data Association AGP: accelerated graphics port IRQ: interrupt request ANSI: American National Standards Institute KB: kilobyte APM: advanced power manager...
Page 248 ANSI defined the ASCII standard and other information processing requirements. AccuPoint: A pointing device antistatic: A material used to prevent integrated into the TOSHIBA the buildup of static electricity. computer keyboard. application: A group of programs adaptor: A device that provides an...
Page 249 cache memory boot: Short for bootstrap. A program does not require a steady stream of that starts or restarts the computer. bits to be transmitted at regular time The program reads instructions from a intervals. storage device into the computer’s memory.
Page 250 capacity capacity: The amount of data that can CMOS: Complementary Metal-Oxide be stored on a magnetic storage Semiconductor. An electronic circuit device such as a diskette (floppy disk) fabricated on a silicon wafer that or hard disk. It is usually described in requires very little power.
Page 251 dialog box computer system: A combination of hardware, software, firmware, and data: Information that is factual, peripheral components assembled to measurable or statistical that a process data into useful information. computer can process, store, or configuration: The specific compo- retrieve. nents in your system (such as the data bits: A data communications terminal, printer, and disk drives) and...
Page 252 disk drive disk drive: The device that randomly DVD-RAM: A Digital Versatile Disc accesses information on a disk and Random Access Memory is a high- copies it to the computer’s memory. It capacity, high performance disc that also writes data from memory to the lets you store large volumes of data.
Page 253 See also and mechanical components of a diskette. computer system: typically, the Fn-esse: A TOSHIBA utility that lets computer itself, external disk drives, you assign functions to hot keys. etc. See also software and firmware. folder: An icon in Windows used to hertz: A unit of wave frequency that store documents or other folders.
Page 254 HW Setup: A TOSHIBA utility that interrupt request: A signal that gives lets you set the parameters for various a component access to the processor.
Page 255 monitor keyboard: An input device contain- ing switches that are activated by main board: See motherboard. manually pressing marked keys. Each keystroke activates a switch that megabyte (MB): A unit of data transmits a specific code to the storage equal to 1024 kilobytes. See computer.
Page 256 motherboard characters and input them into a motherboard: A name sometimes storage device. used to refer to the main printed circuit board in processing equipment. It online state: A functional state of a usually contains integrated circuits peripheral device when it is ready to that perform the processor’s basic receive or transmit data.
Page 257 Class B computing device or other computers. regulations. Power Saver Utility: A TOSHIBA Random Access Memory (RAM): utility that lets you set the parameters High speed memory within the for various power-saving functions.
Page 258 RGB: Red, green, and blue. A device SIO: Serial Input/Output. The that uses three input signals, each electronic methodology used in serial activating an electron gun for a data transmission. primary additive color (red, green, and soft key: Key combinations that blue) or port for using such a device.
Page 259 (TFT) to drive each cell. protecting a diskette (floppy disk) from accidental erasure. Touch Pad: A pointing device integrated into the TOSHIBA com- puter palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switch- ing transistors for gates and storage.
Page 260 Glossary Glossary-14 Get other manuals https://www.bkmanuals.com...
Page 261: Index
6-14 Dual Pointing Device 1-6, 1-12 Bluetooth 1-8 AccuPoint 1-6, 2-9 problems 9-24 Touch Pad 1-6 TOSHIBA Stack, utility 1-12 Touch Pad control buttons 2-10 using 4-25 Touch Pad location 2-8 Boot mode 3-7 problems 9-17 Boot priority 7-2...
Page 262 User's manual DVD Video Player 1-12 DVD-ROM drive 1-4, 1-14 Graphics controller 1-6 location 2-4 problems 9-10 using 4-7 Hard disk drive 1-4, 1-14 view 2-15 automatic power off 1-10 problems 9-8 Headphone jack, See Sound system Environment 3-1 Heat dispersal, See Cooling Equipment checklist 1-1 Hibernation 1-11 Equipment setup...
Page 263 Index Indicators keyboard 2-12 Media care system 2-2, 2-11 CD/DVDs 4-20 Infrared port 1-6 diskettes 4-20 location 2-1 SD card 8-7 problems 9-16 Memory 1-3 Instant security, See Hot keys expansion 1-13 Interfaces, See Ports installing 8-8 problems 9-19 removing 8-13 Keyboard 1-6, 5-1 Microphone jack, See Sound system emulating enhanced keyboard 5-2...
Page 264 9-4 external monitor 1-6 SD card 9-15 i.LINK 1-6 self test 9-4 infrared 1-6 sound system 9-20 USB 1-6 support from TOSHIBA 9-25 Power system start-up 9-3 button location 2-8 USB 9-19 conditions 6-1 Wireless LAN 9-23 indicators 6-4...
Page 265 2-2 Standby 1-11 automatic 1-10 setting 3-10 System indicators, See indicators TOSHIBA Console 1-9 TOSHIBA Console button 1-9, 2-9 TOSHIBA Controls 1-11 TOSHIBA Power Saver 1-11 Touch Pad, See Dual Pointing Device Troubleshooting, See Problems TV 8-21 USB 1-6...
Page 266 User's manual Index-6 Get other manuals https://www.bkmanuals.com...

This manual is also suitable for:

Tecra m1

Toshiba PT930 User Manual

Chapter 1 Introduction

Chapter 2 The Grand Tour

Chapter 3 Getting Started

Chapter 4 Operating Basics

Chapter 5 The Keyboard

Chapter 6 Power and Power-Up Modes

Chapter 7 HW Setup

Chapter 8 Optional Devices

Chapter 9 Troubleshooting

Appendix A Specifications

Appendix D S-Registers

Quick Links

Related Manuals for Toshiba PT930

Summary of Contents for Toshiba PT930

This manual is also suitable for:

Table of Contents