Page 1 TECRA S3 TOSHIBA TECRA S3 Portable Personal Computer User’s Manual...
Page 2 This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA TECRA S3 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
Page 3: Fcc Information
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, parallel port, serial port,...
Page 4 User’s Manual EU Declaration of Conformity TOSHIBA declares, that the product: PTS30* conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...
Page 5 User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04...
Page 6 User’s Manual One of the labels is located on the module. Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the modem ■...
Page 7: Type Of Service
FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 8 User’s Manual Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Page 9 User’s Manual Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
Page 10 User’s Manual ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and b/ The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the...
Page 11: General Conditions
User’s Manual ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
Page 12 User’s Manual Description on Laser specification The optical drive such as DVD-ROM&CD-R/RW drive and DVD Super Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE...
Page 13: Table Of Contents
TECRA S3 Table of Contents Preface Manual contents ......... . xxi Conventions.
Page 14 Operating Basics TOSHIBA Dual Pointing Device ......4-1 Using the Touch Pad ........4-1 Using the AccuPoint .
Page 15 TOSHIBA Mic Effect ........4-29...
Page 16 Using the Hard Disk Drive (HDD) Protection ....4-39 TOSHIBA HDD Protection Properties ..... . . 4-40 Details .
Page 17 Replacing the battery pack....... . . 6-12 TOSHIBA Password Utility ....... . . 6-13 User Password .
Page 18 TV ........... . . 8-16 Using the TOSHIBA Assist button......8-16 Changing the resolution .
Page 19 TOSHIBA support ........
Page 20 Appendix C AT Commands Appendix D S-registers Appendix E V.90 Appendix F Wireless LAN Appendix G TOSHIBA RAID Appendix H Bluetooth wireless technology Interoperability Appendix I AC Power Cord and Connectors Appendix J TOSHIBA Anti-theft Protection Timer Glossary Index User’s Manual...
Page 21: Manual Contents
This manual tells how to set up and begin using your TECRA S3 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 22: Conventions
Preface Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password. Chapter 7, Setup, explains how to configure the computer using the HW Setup program and TPM. Chapter 8, Optional Devices, describes the optional hardware available.
Page 23: Key Operation
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 24 Preface xxiv User’s Manual...
Page 25: General Precautions
TECRA S3 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 26: Pc Card Overheating
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system.
Page 27: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 28: Software
If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: User’s Manual...
Page 29 Introduction Processor Built-in The computer is equipped with an Intel ® processor. ® ® Intel Pentium M processor, which incorporates a 2 MB level 2 cache memory and supports Enhanced Intel ® SpeedStep technology. ® ™ Some models of the computers carry Intel Centrino technology, which is ®...
Page 30: Optical Media Drive
Introduction RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure.
Page 31 Introduction DVD-ROM&CD-R/RW Some models are equipped with a full-size, DVD- drive ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum 24 speed.
Page 32 Refer to Chapter 5, Keyboard, for details. TOSHIBA Dual Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows.
Page 33 Introduction Universal Serial Bus The computer has Universal Serial Bus ports that (USB 2.0) comply with the USB 2.0 standard. Docking This port enables connection of an optional Advanced Port Replicator III described in the Options section. i.LINK™ (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras.
Page 34 Introduction Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line.
Page 35 Ultra Slim Bay is a single-drive bay that Modules accommodates a DVD-ROM&CD-R/RW drive, DVD Super Multi drive and secondary hard disk drive. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system. Security...
Page 36: Special Features
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Assist Press this button to launch an application button automatically. The default is TOSHIBA Assist.
Page 37 LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Actions tab in TOSHIBA Power Saver. Low battery When battery power is exhausted to the point that...
Page 38: Utilities
Buttons: Assign applications or functions to the TOSHIBA Presentation button (default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768) and to the TOSHIBA Assist button (default setting is the TOSHIBA Assist). 1-12 User’s Manual...
Page 39 “shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Fn-esse. DVD Video Player The DVD Video Player is used to play DVD- Video.
Page 40 Advanced Port Repricator III. To open the property dialog, select TOSHIBA Mobile Extension from TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.
Page 41 Device with Fn + F9 keys. To customize the functions of TOSHIBA Dual Pointing Device easily. TOSHIBA Mic Effect TOSHIBA Mic Effect is a utility used to enable comfortable calls with echo cancellation function. The echo cancellation function removes or reduces any harsh echoes or howling sounds that occur when playing audio sounds recorded with a microphone through the speakers.
Page 42: Options
A 256, 512 or 1,024 MB memory module (DDR2- 533/400) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. High capacity An additional battery pack can be purchased battery pack from your TOSHIBA dealer.
Page 43 Introduction Advanced Port The Advanced Port Replicator III provides the Replicator III ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™ (IEEE1394) port, line-in jack and line-out jack, External monitor port, Universal Serial Bus port (USB2.0) ×...
Page 44 Introduction 1-18 User’s Manual...
Page 45: The Grand Tour
TECRA S3 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Disclaimer (Non-applicable Icons) For more information on the Disclaimer regarding Non-applicable Icons, please refer to the Disclaimers section in Chapter 10. Click the *7.
Page 46 The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality.
Page 47: Left Side
The Grand Tour Left side Figure 2-2 shows the computer’s left side. LAN active ExpressCard eject button indicator (orange) Cooling vents ExpressCard slot Video-out jack Link indicator (green) SD card slot LAN jack PC card eject button PC card slot External monitor port Security lock slot Figure 2-2 The left side of the computer...
Page 48 The Grand Tour External monitor This external monitor port lets you connect an port external video display. Video-out jack Plug an S-Video cable into this jack for video-out. The S-Video cable carries video signal. ExpressCard slot The ExpressCard slot can accommodate an ExpressCard.
Page 49: Right Side
The Grand Tour Right side Figure 2-3 shows the computer’s right side. Ultra Slim Bay Modem jack USB ports Serial port Figure 2-3 The right side of the computer Universal Serial Bus Two Universal Serial Bus ports are on the right (USB 2.0) ports side.
Page 50: Back Side
The Grand Tour Ultra Slim Bay A DVD-ROM&CD-R/RW drive, DVD Super Multi drive and Ultra Slim Bay HDD adaptor can be installed in the Ultra Slim Bay. Serial port Use this 9-pin port to connect serial devices such as an external modem, serial mouse or serial printer.
Page 51: Underside
The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Notches Battery lock Battery Battery pack release latch Ultra Slim Bay Docking port Memory module cover Ultra Slim Bay latch Hard disk drive HDD pack cover screw...
Page 52 The Grand Tour Ultra Slim Bay See the Right side section in this chapter for details. Ultra Slim Bay latch Slide the latch to release or secure the Ultra Slim Bay ejector. Be sure to lock the Ultra Slim Bay latch before you transport or carry the computer.
Page 53: Front With The Display Open
Touch Pad control buttons Touch Pad LCD Sensor switch (Not shown) TOSHIBA Presentation button Figure 2-6 The front of the computer with the LCD panel open Display hinge The display hinge holds the LCD display panel at easy-to-view angles. Fingerprint Sensor...
Page 54 The Grand Tour Display screen The LCD screen displays high-contrast text and graphics. The available resolution depends on the model. With XGA, you can change the resolution between 800 × 600 and 1024 × 768 pixels. With SXGA, between 800 × 600 and 1400 ×...
Page 55 Hibernation Mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Special features, for details on settings.
Page 56: System Indicators
The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. Figure 2-7 System indicators SD card The SD card indicator glows green when the computer is accessing the SD card slot. DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor.
Page 57: Keyboard Indicators
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
Page 58: Usb Floppy Disk Drive
The Grand Tour USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. It is supplied as standard with some models and as an option with others. USB connector Disk-In-Use Indicator Floppy disk...
Page 59: Optical Media Drives
The Grand Tour Optical media drives One of the following optical media drives is installed in the computer: DVD- ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical media drives...
Page 60: Formats
The Grand Tour Formats The drives support the following formats: ■ ■ CD-ROM DVD -Video ■ ■ DVD-ROM CD-Text ■ ■ CD-DA CD-ROM Mode 1, Mode 2 ■ ■ Enhanced CD (CD-EXTRA) Photo CD (single/multi-session) ■ ■ Addressing Method 2 CD-ROM XA Mode 2 (Form1, Form2) DVD-ROM&CD-R/RW drive...
Page 61: Ac Adaptor
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer.
Page 62 The Grand Tour Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC.
Page 63: Getting Started
TECRA S3 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 64: General Conditions
PC, it could cause a system failure, malfunction or loss of data. If dust contaminates the PC, do not turn on the power. Take it to an authorized Toshiba service provider before you use it. ■ Never place your PC near an object that generates a magnetic field, such as a speaker or TV.
Page 65: Placement Of The Computer
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.
Page 66: Seating And Posture
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Figure 3-1 Posture and positioning of the computer ■...
Page 67: Lighting
Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■...
Page 68: Strategic Rest Breaks
Getting Started Strategic Rest Breaks Take short, strategically spaced rest breaks to avoid eye strain and body discomforts. For more specific recommendations on the safety and comfort of your computer environment, customers in the United States may visit the United States Department of Labor, Occupational Safety &...
Page 69 Getting Started ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
Page 70: Opening The Display
Getting Started Figure 3-3 Connecting the power cord to the AC adaptor (3-pin plug) The Universal AC Adaptor and power cord bundled with this product may differ depending on the product model. Depending on the model, a 2-pin plug or 3-pin plug set of the above may be bundled. 2.
Page 71: Turning On The Power
Getting Started 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly. Adjust the angle of the panel to provide optimal clarity. Use reasonable care when opening and closing the LCD display panel. Opening it vigorously or slamming it shut could damage the computer.
Page 72: Starting Up For The First Time
Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.
Page 73 Getting Started ■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby Mode, press the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
Page 74: Hibernation Mode
Getting Started 3. Press the power button. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. When you turn the power back on, you can continue where you left when you shut down the computer.
Page 75 For the computer to shut down in Hibernation Mode, this feature must be enabled in two places: the Hibernate tab in Power Options and Setup Actions tab in TOSHIBA Power Saver. If you do not configure this feature, the computer will shut down in Standby Mode - if battery power becomes depleted, data saved in Standby Mode will be lost.
Page 76: Restarting The Computer
Getting Started Data save in Hibernation Mode When you turn off the power in Hibernation Mode, the computer takes a moment to save current memory data to the hard disk. During this time, the HDD indicator will light. After you turn off the computer, and the content of memory has been saved to the hard disk, turn off the power to any peripheral devices.
Page 77: Restoring The Preinstalled Software From The Recovery Hdd
1. Load the Recovery Media in the optional optical media drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. User’s Manual 3-15...
Page 78 Getting Started 3. Use the left or right cursor key to select the CD-ROM icon in the display menu. For details, refer to the Boot Priority section in Chapter 7, HW Setup. 4. A menu appears. Press the “1” key on the keyboard to restore all hard disk.
Page 79: Operating Basics
This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.
Page 80: Using The Accupoint
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.
Page 81: Using The Fingerprint Sensor
Operating Basics 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
Page 82 Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
Page 83: Points To Note About The Fingerprint Utility
Operating Basics The following illustrations show the correct way to slide your finger over the recognition sensor. Align the finger and sensor like the drawings. Points to note about the Fingerprint Utility The user should back up the user profile information when using the functions provided in this software to encrypt files or folders.
Page 84: Set Up Procedure
Operating Basics Set Up Procedure Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required authentication data using the "OmniPass Enrollment Wizard". The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration.
Page 85: Window Logon Via Fingerprint Authentication
Operating Basics 8. Click Yes when the following message appears: "OmniPass has successfully created the new user. Would you like OmniPass to log on the new user? Once logged on, passwords can be remembered for the new user." This completes the fingerprint registration process. Window Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows.
Page 86: Fingerprint System Boot Authentication
■ It is necessary to register the User Password before using the Fingerprint System Boot Authentication and its extended function, the Fingerprint Single Touch Boot Feature. Please use TOSHIBA Password Utility to register the User Password. ■ The Single Touch Boot Feature cannot function if Windows’s secure logon function (requiring users to press Ctrl + Alt + Del) is set to ON.
Page 87: Fingerprint Single Touch Boot Feature
User/BIOS Password and Windows Logon password before using the Fingerprint System Boot Authentication and this Fingerprint Single Touch Boot Feature. Please use TOSHIBA Password Utility to register your User/ BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon password.
Page 88: How The Swipe The Finger
TOSHIBA does not guarantee that the Fingerprint utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Page 89: Using The Usb Floppy Disk Drive
Operating Basics Using the USB floppy disk drive The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. It is supplied as standard with some models and as an option with others.
Page 90: Changing Ultra Slim Bay Modules
RW drive, DVD Super Multi drive and HDD adaptor. To avoid injury, do not put your hand into the Ultra Slim Bay slot. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction for information on using this utility to change modules while the computer’s power is on.
Page 91: Inserting A Module
Operating Basics Inserting a module Insert the Ultra Slim Bay HDD adaptor as described below. 1. Insert the Ultra Slim Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2. If you want to lock the Ultra Slim Bay HDD adaptor, set the Ultra Slim Bay lock screw in the hole for the lock position (➁).
Page 92: Loading Discs
Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-6 to 4-9. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject button Figure 4-6 Pressing the eject button 2.
Page 93 Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-8 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray.
Page 94: Removing Discs
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/ DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.
Page 95: How To Remove Cd/Dvd When The Disc Tray Will Not Open
Operating Basics 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Page 96: Before Writing Or Rewriting
RICOH Co., Ltd. Ultra-Speed CD-RW: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.
Page 97: When Writing Or Rewriting
Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste as the original data will be lost if there is a write error. ■...
Page 98: Important Message
Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 99 Operating Basics DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD+R DL: MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Hitachi Maxell Ltd.
Page 100: When Writing Or Rewriting
Operating Basics ■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc. ■ Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB.
Page 101: Recordnow! Basic For Toshiba
Always copy data from the hard disk drive to the optical media. Do not use cut-and-paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■...
Page 102: Data Verification
3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).
Page 103: When Using Windvd Creator Platinum
Operating Basics When using WinDVD Creator Platinum You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound appears choppy - in this instance please follow the instructions below: 1.
Page 104 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.
Page 105: Media Care
Operating Basics ■ WinDVD Creator cannot export to DVD-Audio, VideoCD or miniDVD format. ■ WinDVD Creator can write DVD-RAM/+RW in VR format, but the disc may only play on your computer. ■ When writing to a DVD disc, WinDVD Creator requires 2GB or more of disk space for every one hour of video.
Page 106: Floppy Disks
Operating Basics Floppy disks 1. Store your floppy disks in the container they came in to protect them and keep them clean. If a floppy disk is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2.
Page 107: Microphone Level
Adjust the equalizer settings to enhance sound quality. TOSHIBA Mic Effect TOSHIBA Mic Effect is a utility used to enable comfortable calls with echo cancellation function. The echo cancellation function removes or reduces any harsh echoes or howling sounds that occur when playing audio sounds recorded with a microphone through the speakers.
Page 108: Modem
Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 109: Properties Menu
Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system.
Page 110 Operating Basics ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■...
Page 111: Disconnecting
Operating Basics Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner.
Page 112: Bluetooth Wireless Technology
■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth™...
Page 113: Wireless Communication Switch
TOSHIBA 1. Install: ® On Windows2000 or Windows XP, Bluetooth Stack for Windows TOSHIBA does not have a digital signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth Stack.
Page 114: Wireless Communication Indicator
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Page 115: Connecting Lan Cable
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.
Page 116: Cleaning The Computer
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 117: Using The Hard Disk Drive (Hdd) Protection
Operating Basics Using the Hard Disk Drive (HDD) Protection This computer has a function for reducing the risk of damage on hard disk drive. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks, and those signs in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact.
Page 118: Toshiba Hdd Protection Properties
Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting.
Page 119: Details
Operating Basics Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Figure 4-16 Details Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
Page 120: Heat Dispersal
CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. When the CPU temperature falls to a normal range, the fan is turned off and the CPU operation returns to standard speed.
Page 121: The Keyboard
TECRA S3 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 122: Function Keys: F1
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 123: Hot Keys
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
Page 124 F2 again to toggle between the settings. Release both Fn and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters the Standby Mode.
Page 125 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.
Page 126: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 127: Windows Special Keys
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button.
Page 128: Temporarily Using Normal Keyboard (Overlay On)
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard...
Page 129: Temporarily Changing Modes
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation.
Page 130 The Keyboard 5-10 User’s Manual...
Page 131: Power And Power-Up Modes
TECRA S3 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 132: Power Indicators
Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) Battery charge • Operates adaptor is above low • LED: Battery off battery trigger DC IN off connected point Battery charge • Operates is below low •...
Page 133: Dc In Indicator
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Indicates the AC adaptor is connected and Green supplying proper power to the computer. Indicates a problem with the power supply. Plug Flashing orange the AC adaptor into another power outlet.
Page 134: High Capacity Battery Pack (Option)
The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not remove the battery pack while the computer is in Standby Mode.
Page 135: Real Time Clock (Rtc) Battery
The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Page 136 Power and Power-Up Modes 3. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or a fire, and could also damage the battery pack. Always wrap the battery pack in plastic (or place it in a plastic bag) whenever transporting it, to avoid exposing the terminals to another conductive object which could result in serious injury.
Page 137 16. Keep the battery pack out of reach of infants and children. It can cause injury. Caution 1. Use only battery packs recommended by TOSHIBA as replacements. 2. When installing a battery pack or before moving the PC, always make sure the battery pack is inserted correctly and securely. If the battery falls out, while you are carrying the PC, you could be injured or the battery pack could be damaged.
Page 138: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 139: Battery Charging Notice
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off High capacity battery pack (8800mAh) about 5.0 to 21.5 about 4.5 Battery pack (4700mAh) about 3.5 to 13.0 about 3.0 RTC battery...
Page 140: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 141: Retaining Data With Power Off
Power and Power-Up Modes ■ The condition of the battery terminals. Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the battery pack. Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type...
Page 142: Replacing The Battery Pack
Power and Power-Up Modes Replacing the battery pack The battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging. It will need to be replaced when it reaches the end of its operating life.
Page 143: Toshiba Password Utility
Battery lock Figure 6-2 Securing the battery pack 9. Turn your computer over. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Page 144 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: start ->...
Page 145: Supervisor Password
Register, delete or change the Supervisor Password. ■ Create or invalidate a Supervisor Password token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ■ Specify restrictions for general users.
Page 146: Power-Up Modes
Chapter 3, Getting Started. Windows utilities You can configure various settings associated with both Standby Mode and Hibernation Mode within TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby Mode and Fn + F4 to enter Hibernation.
Page 147: Hw Setup
TECRA S3 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
Page 148: Power On Display
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
Page 149: Boot Priority
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD- The computer looks for bootable files in the ROM −> LAN following order: HDD, floppy disk drive* , CD- ROM* and LAN (Default).
Page 150 HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Ultra Slim Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot.
Page 151 HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. The priority is set as built-in HDD ->...
Page 152 HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key (PS/2 keyboard only).
Page 153 HW Setup This function lets you set the CPU operating mode. ® This option is displayed only for models with a Pentium-M processor. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled.
Page 154: Device Config
HW Setup Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control Setup by OS (Default). Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode.
Page 155: Configuring The Execute-Disable Bit Capability And Tpm
■ In most cases, changes to the system's configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth. If you make changes to the...
Page 156: Execute-Disable Bit Capability
Capability so that it is not available for use. (Default). System configuration changes, other than changes to this setting, should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.
Page 157: Security Controller
■ System configuration changes other than changes to this setting should be made in Windows using TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Device Manager, etc. ■ When using TPM, please install the Infineon TPM Installation Guide from the TOSHIBA Application Installer.
Page 158 HW Setup 7-12 User’s Manual...
Page 159: Optional Devices
TECRA S3 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ ExpressCard ■...
Page 160: Pc Card
The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 161: Removing A Pc Card
ExpressCard The computer is equipped with an ExpressCard slot. Any ExpressCard that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports hot plug connection and utilizes the PCI- Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5 Gbps.
Page 162: Removing An Expresscard
Optional Devices 2. Press gently to ensure a firm connection. ExpressCard slot ExpressCard Figure 8-3 Inserting the ExpressCard 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configuration in Windows to make sure it is appropriate for your ExpressCard. Removing an ExpressCard To remove the ExpressCard, follow the steps below.
Page 163: Sd Card
TOSHIBA SD memory card format utility, not with the format commands provided within Windows. In order to run TOSHIBA SD memory card format, click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.
Page 164: Removing An Sd Card
Optional Devices ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost. Removing an SD card To remove an SD card, follow the steps below.
Page 165: Sd Card Care
Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk Within the TOSHIBA SD Memory Boot Utility, a bootable SD memory card can be created if required. Refer to the...
Page 166: Installing Memory Module
Optional Devices ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions as you can damage the computer and/or the module, and you risk losing data: a. The computer is turned on.
Page 167 Optional Devices 5. Slide your fingernail or a thin object under the cover and lift it off. Memory module cover Screw Figure 8-7 Removing the memory module cover 6. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 45 degree angle before pressing it down until the latches on either side snap into place.
Page 168: Removing Memory Module
Optional Devices 7. Seat the memory module cover and secure it with one screw. Be sure that the cover is closed firmly. Screw Memory module cover Figure 8-9 Seating the memory module cover 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details.
Page 169: Battery Pack
Optional Devices 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.
Page 170: Battery Charger
Optional Devices Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). Hard disk drive pack An extra hard disk drive expands the flexibility of your system and lets you carry your data without carrying the computer.
Page 171: Installing The Hard Disk Drive Pack
Optional Devices 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector. Hard disk drive pack Plastic tab Figure 8-12 Removing the hard disk drive pack Installing the hard disk drive pack To install the hard disk drive pack, follow the steps below.
Page 172: Ultra Slim Bay Hdd Adaptor (Black)
Optional Devices Ultra Slim Bay HDD adaptor (Black) You can increase your computer’s data storage capacity by installing an additional 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.16 GB) hard disk drive in the Ultra Slim Bay. To install an hard disk drive in the Ultra Slim Bay HDD adaptor follow the steps below.
Page 173: Usb Floppy Disk Drive
Optional Devices 3. Close the lid and slid the lock to the lock position. Figure 8-16 Closing the lid For details on inserting the Ultra Slim Bay HDD adaptor in the computer’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics.
Page 174: Using The Toshiba Assist Button
You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, Keyboard. To use "TV OUT" function by "TOSHIBA Assist button", it is necessary to change the settings of "TOSHIBA Assist button" in advance. To open "TOSHIBA Controls" properties, click start, click Control Panel, click Printers and Other Hardware, select "TOSHIBA Controls", and set...
Page 175: Changing The Resolution
Optional Devices If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. Click the Settings tab and click the Advanced button. d.
Page 176: I.link (Ieee1394)
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 177: Connecting
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Figure 8-19 Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■...
Page 178: Advanced Port Replicator Iii
Optional Devices Advanced Port Replicator III In addition to the ports available on the computer, the Advanced Port Replicator III provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator connects directly to the docking interface on the underside of the computer.
Page 179: Parallel Printer
7. Turn on the computer’s power. 8. Start the HW Setup program. Refer to Chapter 7, Setup. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect.
Page 180: Security Lock
Optional Devices 2. Connect the serial connector to the serial port and tighten the screws on the left and right hand side. Serial port Serial connector Figure 8-20 Connecting the serial connector to the serial port Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III.
Page 181: Troubleshooting
TECRA S3 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 182: Preliminary Checklist
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 183: Hardware And System Checklist
Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.
Page 184: Self Test
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...
Page 185: Ac Power
Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down Indicates a problem with the heat dispersal and its DC IN indicator system. Please contact your dealer. is flashing green AC power If you have trouble turning on the computer with the AC adaptor connected,...
Page 186 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...
Page 187: Password
Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.
Page 188: Internal Lcd Display Panel
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
Page 189: Dvd-Rom&Cd-R/Rw Drive
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power.
Page 190: Dvd Super Multi Drive
Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.
Page 191: Usb Floppy Disk Drive
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive.
Page 192: Pc Card
Troubleshooting PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation.
Page 193: Dual Pointing Device
Device tab. Then click the Detail Setting button and click the Device Select tab. Check that the Touch Pad is not selected. Pressing Fn + F9 to enables TOSHIBA Dual Pointing Device. On-screen pointer The system might be busy. If the pointer is...
Page 194: Fingerprint Sensor
Troubleshooting USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume its mouse operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.
Page 195: Usb Device
Troubleshooting Problem Procedure Fingerprint System Please use TOSHIBA Password Utility to register Boot Authentication or the User Password if it was not registered. Single Touch Boot Set the Enable System Boot Authentication feature cannot be checkbox from PBA Settings in the OmniPass enabled.
Page 196: Memory Expansion
Troubleshooting Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure Beep sounds. Make sure the memory module installed in the memory slot is compatible with the computer. (Two beeps, a dash and a dot, for a If an incompatible module has been installed, defective memory follow the steps below.
Page 197: External Monitor
Troubleshooting External monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
Page 198: Modem
Troubleshooting Modem Refer to Appendix C, AT Commands and Appendix D, S-registers. Problem Procedure Communication Make sure the computer’s internal modem software can’t initialize settings are correct. Refer to Phone and Modem modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make a sure the communication application’s tone dial...
Page 199: Lan
Troubleshooting Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub. Wake-up on LAN does Make sure the AC adaptor is connected. The not work Wake-up on LAN function consumes power even when the system is off.
Page 200: Printer
Troubleshooting Printer Refer also to the Parallel printer sections in Chapter 8, Optional Devices, and to the troubleshooting and other relevant sections in your printer and software documentation. Problem Procedure Printer does not turn on. Check that the printer is connected to an electric outlet.
Page 201: Disposing Of Pc And Pc Batteries
All data deletion costs will be borne by you. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 202: Where To Write
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia Germany & Austria TOSHIBA Australia Pty. Ltd.
Page 203 TOSHIBA Information Systems Systems, Inc. (U.K.) Ltd. 9740 Irvine Boulevard TOSHIBA Court Irvine, California 92618 Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany User’s Manual 9-23...
Page 204 Troubleshooting 9-24 User’s Manual...
Page 205: Cpu*1
TECRA S3 Chapter 10 Disclaimers This chapter states the Disclaimer(s) information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Disclaimer description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual.
Page 206: Battery Life*2
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 207: Graphics Processor Unit ("Gpu")*5
Disclaimers Graphics Processor Unit ("GPU”) Graphics processor unit ("GPU") performance may vary depending on product model, design configuration, applications, power management settings and features utilized. GPU performance is only optimized when operating in AC power mode and may decrease considerably when operating in battery power mode.
Page 208 Disclaimers 10-4 User’s Manual...
Page 209: Appendix A Specifications
TECRA S3 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.85 kilograms, configured with: 15”SXGA+, 256MB RAM, 40GB HDD, DVD-ROM&CD-R/RW drive, modem, LAN, Wireless LAN, 6cell battery pack. Weight will vary with other configurations. Above weights are measured at specific criteria.
Page 210 Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands...
Page 211 Specifications Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
Page 212 Specifications User’s Manual...
Page 213: Appendix B Display Controller And Modes
TECRA S3 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel.
Page 214 Display Controller and Modes Table1 Video modes (VGA) Video mode Type Resolution Character Colors Scanning matrix frequency (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K Text Characters 2, 3 80 × 25 8 × 8 16 of 256K Text Characters...
Page 215 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Colors Scanning mode matrix frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K Grph Pels 640 ×...
Page 216 Display Controller and Modes Table 2 Video modes (XGA model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual with LCD only) 1600 ×...
Page 217 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual with LCD only) 1600 ×...
Page 218 Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual with LCD only) 1600 ×...
Page 219 Display Controller and Modes Table 3 Video modes (SXGA+ model) Resolution Vertical colors colors frequency (Hz)* 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K 1440 × 1050 256/256K 256/256K 1600 ×...
Page 220 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K 1440 × 1050 64K/64K 64K/64K 1600 ×...
Page 221 Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution Vertical colors colors frequency (Hz)* 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M 1440 × 1050 16M/16M 16M/16M 1600 ×...
Page 222 Display Controller and Modes PowerMizer The PowerMizer function is only available in nVIDIA models. PowerMizer is a graphics processor installed on this computer. The performance of PowerMizer can be configured in three ways. To define the performance, select the menu options shown below: Display Property ->...
Page 223: Appendix C At Commands
TECRA S3 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 224 AT Commands Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default). Selects V.21 when the modem is at 300 bps. Selects Bell 103J when the modem is at 300 bps (default).
Page 225 AT Commands Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default). Modem goes off-hook. Result Codes: n=0,1 ERROR Otherwise Request ID information This command displays product information about the modem.
Page 226 AT Commands Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
Page 227 AT Commands Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
Page 228 AT Commands Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
Page 229 AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory.
Page 230 AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
Page 231 AT Commands V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).
Page 232 AT Commands Result Codes: n=0,3 ERROR Otherwise C-10 User’s Manual...
Page 233: Appendix D S-Registers
TECRA S3 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
Page 234 S-registers Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
Page 235 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
Page 236 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range: 0-255 Default: 2 Units:...
Page 237 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...
Page 238: At Command Set Result Codes
S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
Page 239 S-registers CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
Page 240 S-registers User’s Manual...
Page 241 TECRA S3 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 242 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
Page 243 V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
Page 244 V.90 User’s Manual...
Page 245: Appendix F Wireless Lan
TECRA S3 Appendix F Wireless LAN Card Specifications Form Factor Mini PCI Type III ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Page 246 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 247 Wireless LAN 2457* 2462 2467* 2472* *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■...
Page 248 Wireless LAN 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825 User’s Manual...
Page 249: Appendix G Toshiba Raid
Please refer to the TOSHIBA RAID help for details. ■ By changing this setting you are reconfiguring your hard disk.
Page 250: Windows Manual Setup
3. When the message "Setup will load support for the following mass storage device(s):" appears on the screen, press the S key and install the TOSHIBA RAID Driver using the TOSHIBA RAID Driver Disk that was created. 4. Follow the onscreen instructions to continue Windows setup.
Page 251 An effective way to ensure that such situations do not happen is to carry out RAID-1 media checks regularly. The TOSHIBA RAID utility is set as default to carry out media checks every month on the third Wednesday from noon.
Page 252: Starting The Bios Setup Program
TOSHIBA RAID Starting, Modifying and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Switch on your computer while pressing the Esc key. If Password = is displayed, enter the User Password and press the Enter key. Please refer to Chapter 6, the...
Page 253: Ending The Bios Setup Program
TOSHIBA RAID 3. The Execute Creation message is displayed once the configuration is modified. Move the cursor to the appropriate location and press the space bar to continue. Pressing the Home key will revert the modified Create State settings back to the Current State settings.
Page 254 TOSHIBA RAID User’s Manual...
Page 255: Appendix H Bluetooth Wireless Technology Interoperability
Appendix H Bluetooth wireless technology Interoperability Bluetooth Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver2.0+EDR, as defined and approved by The Bluetooth Special Interest Group.
Page 256 TOSHIBA portable computers. Always use Bluetooth Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe...
Page 257: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 258 -Consult the dealer or an experienced radio/TV technician for help. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Bluetooth Card from TOSHIBA, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
Page 259 FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used in this device are located at the upper edge of the LCD screen, and this device has been tested as portable device as defined in Section 2.1093 of FCC rules when the LCD screen is rotated 180 degree...
Page 260 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 261: Device Authorization
Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday: 10:00-17:00 Toll Free Tel : 0120-15-1048 Direct Dial : 03-3457-4850 : 03-3457-4868 Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law.
Page 262: Wireless Technology
Bluetooth wireless technology Interoperability Approved Countries/Regions for use (Bluetooth wireless technology) Bluetooth Card from TOSHIBA equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 263: Appendix I Ac Power Cord And Connectors
TECRA S3 Appendix I AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following...
Page 264 AC Power Cord and Connectors France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.
Page 265: Appendix J Toshiba Anti-Theft Protection Timer
BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility. The settings can only be activated or modified by a user with supervisor authority.
Page 266 TOSHIBA Anti-theft Protection Timer User’s Manual...
Page 267: Glossary
TECRA S3 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange...
Page 268 VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Page 269 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
Page 270 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
Page 271 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 272 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Page 273 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 274 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 275 Glossary jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
Page 276 Glossary mode: A method of operation, for example, the boot mode, Standby Mode or the Hibernation Mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
Page 277 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 278 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
Page 279 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 280 Glossary Glossary-14 User’s Manual...
Page 281 B-1 Battery hinge 2-9 charging 6-8 opening 3-8 extending life 6-11 screen 2-10 indicator 2-12 DLA for TOSHIBA 1-15 4-24 location 2-7 Docking interface 1-7 monitoring capacity 6-10 Documentation list 1-2 real time clock 1-4 Dual Pointing Device 1-6...
Page 282 Index location 2-6 brightness increases) 5-5 problems 9-9 Fn + F8 (wireless setting) 5-5 using 4-13 Fn + F9 (Dual Pointing Device) writing 4-17 Fn + space (LCD screen resolu- tion selection) 5-6 Environment 3-1 Fn + Tab (Optical media drive Equipment checklist 1-1 power icon) 5-6 Equipment setup...
Page 283 Index LAN 7-7 Parallel/Printer 7-8 Media care 4-27 USB 7-8 CD/DVDs 4-27 window 7-1 floppy disks 4-28 SD card 8-7 i.LINK 1-7 8-18 Memory 1-3 connecting 8-19 expansion 1-16 disconnecting 8-19 problems 9-16 precautions 8-18 Modem 1-8 4-30 problems 9-17 connecting 4-31 Indicators 2-12 disconnecting 4-33...
Page 284 Index hibernation mode 3-12 Sound system 9-16 indicators 6-2 System start-up 9-3 panel on/off 1-11 6-16 TOSHIBA support 9-21 shut down mode (boot Touch Pad/AccuPoint 9-13 mode) 3-10 TV output signal 9-20 standby mode 3-10 USB 9-15 system auto off 6-16...
Page 285 TOSHIBA ConfigFree 1-14 TOSHIBA Controls 1-12 TOSHIBA Dual Pointing Device utility 1-15 TOSHIBA Mic Effect 1-15 TOSHIBA Mobile Extension 1- TOSHIBA PC Diagnostic Tool 1- TOSHIBA Power Saver 1-12 TOSHIBA Presentation button 1-10 TOSHIBA SD Memory Boot Util- ity 1-14...
Page 286 Index Index-6 User’s Manual...

This manual is also suitable for:

Pts30

Toshiba tecra s3 User Manual

Preface

Manual Contents

Conventions

General Precautions

Stress Injury

Heat Injury

Pressure or Impact Damage

PC Card Overheating

Mobile Phone

Introduction

Equipment Checklist

Features

Special Features

Utilities

Options

The Grand Tour

Front with the Display Closed

Left Side

Right Side

Back Side

Underside

Front with the Display Open

System Indicators

Keyboard Indicators

USB Floppy Disk Drive

Optical Media Drives

AC Adaptor

Getting Started

Setting up Your Work Space

Connecting the AC Adaptor

Opening the Display

Turning on the Power

Starting up for the First Time

Turning off the Power

Restarting the Computer

Create Optical Recovery Discs

Restoring the Preinstalled Software from the Recovery HDD

Restoring the Preinstalled Software from Your Creating Recovery Media

Operating Basics

TOSHIBA Dual Pointing Device

Using the Fingerprint Sensor

Using the USB Floppy Disk Drive

Changing Ultra Slim Bay Modules

Using Optical Media Drives

Writing Cds on DVD-ROM&CD-R/RW Drive

Writing CD/Dvds on DVD Super Multi Drive

Media Care

Sound System

Modem

Wireless Communications

Lan

Cleaning the Computer

Moving the Computer

Using the Hard Disk Drive (HDD) Protection

Heat Dispersal

The Keyboard

Typewriter Keys

Function Keys: F1

Soft Keys: Fn Key Combinations

Hot Keys

Windows Special Keys

Keypad Overlay

Generating ASCII Characters

Power and Power-Up Modes

Power Conditions

Power Indicators

Battery Types

Care and Use of the Battery Pack

Replacing the Battery Pack

TOSHIBA Password Utility

Power-Up Modes

Panel Power On/Off

System Auto off

HW Setup

Accessing HW Setup

HW Setup Window

Configuring the Execute-Disable Bit Capability and TPM

Optional Devices

PC Card