Page 1 Satellite Pro User’s Guide If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Customer Support Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 162 in this guide.
Page 2 TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA,...
Page 3 Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's ports.
Page 4: Industry Canada Requirement
Contact either: ❖ Toshiba’s Support Web site at pcsupport.toshiba.com. ❖ Or call the Toshiba Customer Support Center: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003.
Page 5: Telephone Company Procedures
Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Customer Support Center within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Page 6 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment NOTICE: The Industry Canada label identifies certified equipment.
Page 7: Wireless Interoperability
Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined and approved by the Institute of Electrical and Electronics Engineers.
Page 8: Wireless Lan And Your Health
The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Page 9 Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population;...
Page 10 This Directive applies to EU member countries only and does not apply to end users in other countries such as the United States. Although the initial emphasis is in Europe, Toshiba is already working with design engineers, suppliers, and other partners to determine appropriate worldwide product life cycle planning and end-of-life strategies for our products.
Page 11 VCCI Class B Information Modem Warning Notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 12 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 13: Device Authorization
FH: This equipment uses FH-SS modulation. The interference range of this equipment is less than 10m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850...
Page 14: Radio Approvals For Wireless Devices
Radio Approvals for Wireless Devices NOTE The following information is dependent on what type of wireless device is in your computer. Not all devices are available on all models. Approved Countries/Regions for the Intel Link 5100/5300 Series This equipment is approved to the radio standard by the countries/regions in the following table.
Page 15 Malawi Martinique Monaco Morocco New Zealand Oman Paraguay Poland Qatar Russia San Marino Singapore South Africa Sri Lanka Tahiti Turk Islands United Kingdom Vatican Virgin Islands Approved Countries/Regions for the Atheros Link AR5B95 Series This equipment is approved to the radio standard by the countries/regions in the following table.
Page 16 Finland Ghana Herzegovina Hungary Indonesia Italy Jordan Kuwait Lebanon Lithuania Malaysia Monaco Nambia New Zealand Norway Panama Peru Portugal Romania Senegal Slovak Republic South Korea Sweden Thailand Ukraine Yemen Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique:...
Page 17 Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au- dessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de l’IBPT est requise. Pour les enregistrements et licences, veuillez contacter l’IBPT.
Page 18 European Community Countries Iceland, Spain O: allowed x: forbidden ❖ To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply. The user should use the wireless LAN utility to check the current channel of operation.
Page 19 Approved Countries/Regions for the Realtek This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Albania Austria Bangladesh Bosnia Cambodia China Croatia Denmark Egypt Finland...
Page 20 Approved Countries/Regions for the Realtek This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Albania Austria Bangladesh Bosnia Cambodia China Croatia Denmark Egypt Finland...
Page 21 UAE (United Arab Emirates) Uruguay Vietnam Approved Countries/Regions for the Realtek This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Albania Australia Bahrain Bolivia...
Page 22 Sweden Thailand UAE (United Arab Emirates) Yemen Approved Countries/Regions for use for the ® Intel PRO/Wireless 3945ABG Network Connection This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 23 11a, 11b, 11g and 11n wireless are based on IEEE 802.11a, 802.11b, 802.11g and 802.11n respectively. The IEEE 802.11n specification has not been finalized and is currently in draft release. The TOSHIBA 11a/b/g/n Wireless LAN Adapters are based on the Draft Release, Version 1.0, of the IEEE 802.11n specification.
Page 24: Bluetooth Wireless Technology Interoperability
Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for...
Page 25: Bluetooth Wireless Technology And Your Health
Approved Countries/Regions for use (Bluetooth technology) ® Bluetooth Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Argentina Belgium...
Page 26: Regulatory Statements
The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 27 Never attempt to disassemble, adjust or repair an optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
Page 28 Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 29 Atheros is a registered trademark of Atheros Communications, Inc. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
Page 30: Table Of Contents
Contents Introduction... 37 This guide ...39 Safety icons ...40 Other icons used...40 Your computer’s features and specifications ...41 Other documentation ...41 Service options ...41 Chapter 1: Getting Started... 42 Selecting a place to work ...42 Setting up a work environment ...42 Keeping yourself comfortable ...43 Precautions...43 Important information on your computer’s...
Page 31 Turning on the power ...50 Setting up your software...51 Registering your computer with Toshiba ...51 Adding optional external devices...51 Adding memory (optional) ...52 Installing a memory module ...52 Removing a memory module...57 Checking total memory ...60 Recovering the Internal Storage Drive ...60 Recovering to out-of-box state (recommended recovery method)...61...
Page 32 Contents Using and configuring Hibernation mode ...86 Using and configuring Sleep mode ...88 Closing the display panel ...91 Customizing your computer’s settings...91 Caring for your computer...91 Cleaning the computer ...91 Moving the computer...92 Using a computer lock ...92 Chapter 2: Learning the Basics... 93 Computing tips ...93 Using the keyboard ...94 Character keys ...95...
Page 33 Removing a disc with the computer on...107 Removing a disc with the computer off ...108 Caring for optical discs ...108 Toshiba’s online resources ...108 Chapter 3: Mobile Computing...109 Toshiba’s energy-saver design...109 Running the computer on battery power ...110 Battery Notice ...110 Power management ...111...
Page 34 Using an instant password...147 Using a supervisor password...148 Using a user password ...149 Deleting a user password...150 TOSHIBA Face Recognition Utility...151 TOSHIBA PC Diagnostic Tool Utility...152 Mouse Utility ...153 TOSHIBA Hardware Setup...154 TOSHIBA Zooming Utility...156 TOSHIBA Accessibility ...157 TOSHIBA Service Station ...158...
Page 35 Wireless networking problems...179 DVD operating problems...180 Develop good computing habits ...181 Data and system configuration backup in If you need further assistance...186 Before you contact Toshiba ...186 Contacting Toshiba ...186 Other Toshiba Internet Web sites...187 Toshiba’s worldwide offices...187 ® ...158 ®...
Page 36 Contents Appendix A: Hot Keys/TOSHIBA Cards...189 Hot Key Cards ...189 Using the Hot Key Cards ...190 Application Cards...191 Using the Application Cards...192 Card Case...192 Hot key functions ...193 Volume Mute ...193 Lock (Instant security) ...194 Power plan ...195 Sleep mode ...196 Hibernation mode ...197...
Page 37: Introduction
You can wake the computer from Sleep mode by pressing the power button. See the “Mobile Computing” section of the Toshiba User’s Guide for more information on using power management settings to...
Page 38 (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE. Toshiba requires its computer component suppliers to meet RoHS requirements and verifies its suppliers’ commitment to meeting RoHS requirements by conducting component sampling inspections during the product design approval process.
Page 39: This Guide
Toshiba’s Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/component/options availability are all subject to change without notice.
Page 40: Safety Icons
Introduction Safety icons Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 41: Your Computer's Features And Specifications
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see Goes Wrong” on page Introduction...
Page 42: Chapter 1: Getting Started
Chapter 1 Getting Started This chapter provides tips for using your computer effectively, summarizes how to connect components, and explains what to do the first time you use your computer. The “Instruction Manual for Safety and Comfort,” that is shipped with your computer, contains important safety information.
Page 43: Keeping Yourself Comfortable
Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals. Keeping yourself comfortable The Toshiba Instruction Manual for Safety and Comfort, included with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.
Page 44 Getting Started Selecting a place to work ❖ ❖ Read the “Avoid extended contact between computer base/palm rest and skin” section in the “Instruction Manual for Safety and Comfort” that is shipped with your computer. Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer.
Page 45: Important Information On Your Computer's Cooling Fan
Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep mode).
Page 46: Connecting To A Power Source
TOSHIBA Battery Charger (that may have been provided with your computer), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the computer possibly resulting in serious injury.
Page 47 To connect AC power to the computer: Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 48: Charging The Main Battery
Getting Started Charging the main battery The computer’s main battery light gives you an indication of the main battery’s current charge: ❖ Glows amber while the main battery is being charged (AC adaptor connected) ❖ Glows green when the main battery is fully charged ❖...
Page 49: Using The Computer For The First Time
NOTE Battery life and charge time may vary depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel Facing the front of the computer, locate the center of the display panel.
Page 50: Turning On The Power
Getting Started Using the computer for the first time Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology.
Page 51: Setting Up Your Software
Product registration can be completed by either visiting the Toshiba Web site at http://www.register.toshiba.com, or by clicking Start, All Programs, My Toshiba, and then Toshiba Registration. Failure to complete Product Registration will not diminish Customer rights under the Toshiba standard limited Warranty.
Page 52: Adding Memory (Optional)
NOTE Before adding external devices or memory, Toshiba recommends setting up your software. See Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer.
Page 53 NOTE For this model, Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. If the computer is on, begin at step 1; otherwise, skip to step 3. Click Start.
Page 54 Getting Started Adding memory (optional) Using a small Phillips screwdriver, loosen the screw that secures the memory module slot cover. Back of computer (Sample Illustration) Removing the memory module slot cover Remove the memory module slot cover. Place the screw and the cover in a safe place so that you can retrieve them later.
Page 55 NOTE For this model, Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. Pick up the memory module by its sides, avoiding any contact with its connector.
Page 56 Getting Started Adding memory (optional) Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module.
Page 57: Removing A Memory Module
Re-insert the main battery. For more information on inserting the main battery, see Turn the computer right side up. Make sure to remove the soft cloth from the work surface before restarting the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep mode).
Page 58 Getting Started Adding memory (optional) Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory module. Do not remove the memory module while the computer is in Sleep or Hibernation mode.
Page 59 Gently lift the memory module to a 30-degree angle and slide it out of the slot. Back of computer (Sample Illustration) Removing the memory module Replace the memory module slot cover and secure it using the screw. Re-insert the main battery. For more information on inserting the main battery, see Turn the computer right side up.
Page 60: Checking Total Memory
Getting Started Recovering the Internal Storage Drive TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory module, you can check that the computer has recognized the change. To do this: ❖...
Page 61: Recovering To Out-Of-Box State (Recommended Recovery Method)
DVDs/media before using your system for the first time. For more information on creating DVDs/media, see recovery DVDs/media” on page ❖ The Toshiba Recovery Wizard also provides the option of erasing your internal storage drive, without restoring the information on the drive. See more information.
Page 62 Getting Started Recovering the Internal Storage Drive NOTE During the recovery process it is strongly recommended that your computer be connected to an external power source via the AC adaptor. You can recover the original factory image (returning the computer to its out-of-box state) using the utilities stored on your computer’s internal storage drive or using recovery DVDs/media, if you have created such media.
Page 63 Recovering the Internal Storage Drive When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next. (Sample Image) Selecting a Process screen The Recovery of Factory Default Software screen appears.
Page 64: Recovering To A Custom Size Partition
Getting Started Recovering the Internal Storage Drive Click Next to begin the recovery. When the process is complete, a message displays indicating that the internal storage drive has been recovered. Press any key on the keyboard to restart the computer. Recovering to a custom size partition Recovering to a custom size partition deletes all partitions on the drive and all information stored in those partitions.
Page 65 Click Yes to continue. (Sample Image) Warning screen When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next. (Sample Image) Selecting a Process screen...
Page 66: Recovering Without Changing The Internal Storage Drive Partitions
Getting Started Recovering the Internal Storage Drive The Recovery of Factory Default Software screen appears. Select Recover to a custom size partition. (Sample Image) Recovery of Factory Default Software screen Use the on-screen arrow buttons in The size of drive C: field to set the partition size.
Page 67 Recovering the Internal Storage Drive You can recover the C: drive without affecting other partitions by either using the utilities stored on your computer’s internal storage drive or by using recovery DVDs/media, if you have created such media. To recover using the first method, follow the procedure below.
Page 68 Getting Started Recovering the Internal Storage Drive When the Toshiba Recovery Wizard opens and the Selecting a process screen displays, select Recovery of Factory Default Software and then click Next. (Sample Image) Selecting a Process screen The Recovery of Factory Default Software screen appears.
Page 69: Creating Recovery Dvds/Media
If your optical disc drive is not a writable drive, contact Toshiba Customer Support to obtain the Recovery media for your system. The Toshiba Customer Support Center in the United States is (800) 457-7777; outside the United States it is (949) 859-4273. To create recovery DVDs/media: Click Start, All Programs, My Toshiba, and then Recovery Media Creator.
Page 70: Restoring From Recovery Dvds/Media
When the initial screen displays, press The boot menu appears. Using the arrow keys, select the DVD option and press The Selecting a Process screen appears. Select Toshiba Recovery Wizard and then click Next. If your system offers a choice of Windows operating system, select one at this time.
Page 71: Erasing The Internal Storage Drive
When the Toshiba Recovery Wizard opens and the Selecting a Process screen displays, select Recovery of Factory Default Software and then click Next. Select one of the following options: ❖ Recover to out-of-box state—If you want to recover the original factory image (returning the computer to its out- of-box state).
Page 72 DVD option on the boot menu and then press Toshiba Recovery Wizard, and then click Next. Select Erase the hard disk and then click Next. Choose one of the following options on the Erase the hard disk screen: ❖...
Page 73: Checking The Internal Storage Drive Operating Status
Highlight the internal storage drive in the Volume list to display its status in the lower portion of the screen. Installing drivers and applications The Toshiba Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: Click Start, All Programs, My Toshiba, and then TOSHIBA Application Installer.
Page 74 Getting Started Using the TouchPad™ Primary control button (Sample Illustration) The TouchPad and associated control buttons Refer to the table below for specific instructions on performing each operation. NOTE The pointer is the icon (usually an arrow) that moves on the screen when you slide your finger across the TouchPad or move a mouse connected to your computer.
Page 75 Do the following: Open or activate an Move the pointer to the item you want to open/activate. item Do one of the following: ❖ ❖ Right-click an item Move the pointer to the item you want to right-click. Press and release the secondary control button.
Page 76: Adjusting Touchpad™ Settings
TouchPad setting options vary by computer model. The TouchPad settings are accessible through the Mouse Properties option of the Windows Control Panel. For more information, please visit www.support.toshiba.com, and enter the phrase “Mouse pointer jumps around as you type” into the Search field. Disabling or enabling the TouchPad™...
Page 77: Using External Display Devices
Using external display devices Your computer comes with a built-in display, but you can also connect the following types of external display devices to the video ports described below: ❖ An HDMI™-compatible television or VCR/DVD player via the HDMI Out port ❖...
Page 78: Directing The Display Output When You Turn On The Computer
Getting Started Using external display devices Connecting an external monitor or projector You can easily attach an external monitor or projector to your computer if you need a larger screen. To do this: Read the directions that came with the monitor to see if you first need to install new software.
Page 79: Adjusting The Quality Of The External Display
❖ Built-in display and TV (or other external video device) simultaneously ❖ Built-in display and external monitor (extended desktop) ❖ Built-in display and TV (extended desktop) ❖ External monitor and TV (extended desktop) ❖ Swap-Switch primary display between internal display and external monitor when using extended desktop (Sample Image) Display options window Release the...
Page 80: Connecting A Printer
Getting Started Connecting a printer Connecting a printer NOTE Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly.
Page 81: Setting Up A Printer
Setting up a printer NOTE Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure. If your printer does not support Plug and Play, follow these steps to set it up for the first time. You only need to set up the printer once. Click Start, Control Panel, Hardware and Sound, and then under Devices and Printers, click Add a printer.
Page 82: Options For Turning Off The Computer
Getting Started Turning off the computer Options for turning off the computer Depending on the operating system installed, you have more than one option available for turning off the computer: Shut down, Hibernate, and Sleep. Each option has its advantages. ❖...
Page 83 For information on how to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page Sleep mode The Sleep command places the computer into a power-saving mode. Sleep saves the current state of the computer to memory so that, when you restart the computer, you can continue working from where you left off.
Page 84: Using The Shut Down Command
Getting Started Turning off the computer Using the Shut down command The Shut down command completely shuts down the computer without saving your work or the current state of the computer. This command closes all open programs, shuts down the operating system, and then turns off your computer.
Page 85 The Edit Plan Settings window appears. Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. Double-click Power buttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of Power Options screen Select the options you want from the drop-down lists.
Page 86: Using And Configuring Hibernation Mode
Getting Started Turning off the computer Restarting your computer To start the computer up again, press the power button until the ON/OFF light glows green. If you turn off the computer by closing the display panel, you can start it again by opening the display panel. Using and configuring Hibernation mode To turn off the computer using the Hibernation command: Click Start, and then click the arrow next to the Shut down...
Page 87 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. Double-click Power buttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of Power Options screen Select Hibernate for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC...
Page 88: Using And Configuring Sleep Mode
Getting Started Turning off the computer Click Apply. Click OK. Once the computer is configured, you can place it into Hibernation mode by either pressing the power button or closing the display panel, depending on the Hibernation options set. Starting again from Hibernation mode To start up the computer from Hibernation mode, press the power button until the ON/OFF light glows green.
Page 89 Configuring Sleep mode options You can place the computer into Sleep mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Sleep mode. To use any of these methods, you first need to enable them using the Power Options feature.
Page 90 Getting Started Turning off the computer Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. Double-click Power buttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of Power Options screen Select Sleep for the options you want.
Page 91: Closing The Display Panel
Starting again from Sleep mode To start up the computer from Sleep mode, press the power button until the ON/OFF light glows green. The computer returns to the screen(s) you were using. If you place the computer in Sleep mode by closing the display panel, you can start it again by opening the display panel.
Page 92: Moving The Computer
You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com. (Sample Illustration) Computer lock cable To secure the computer: Wrap the cable through or around some part of a heavy object.
Page 93: Chapter 2: Learning The Basics
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the internal storage drive. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Page 94: Using The Keyboard
Learning the Basics Using the keyboard ❖ Back up your files to external media on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your internal storage drive suddenly fails, you will lose all the data on it unless you have a separate backup copy.
Page 95: Character Keys
Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The space bar creates a space character instead of just passing over an area of the page. ❖ The lowercase letter l (el) and the number 1 are not interchangeable.
Page 96: Special Windows ® Keys
Learning the Basics Using the keyboard through programmed functions when pressed. Used in combination with the key, function keys marked with icons execute specific functions on the computer. For example, ON/OFF. For more information, see page 193. ® Special Windows keys (Sample Illustration) Special Windows Your computer’s keyboard has one key and one button that have...
Page 97: Starting A Program
Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys. To turn the numeric overlay on, press The numeric overlay light glows when the numeric overlay is on. To disable the numeric overlay, hold down the again.
Page 98: Starting A Program From Windows Explorer
Learning the Basics Starting a program NOTE If you pause with your mouse on All Programs, it will open it up. You may need to scroll up or down to see the complete list. Click the program group, in this example, Accessories. The Accessories menu is displayed.
Page 99: Starting A Program Using The Search Programs And Files Field
In the right part of the window, double-click Accessories. Windows folder on the right side of the window. In the right part of the window, double-click wordpad. The operating system opens WordPad. To close the program, click the Close button in the upper-right corner of the program’s window.
Page 100 Learning the Basics Saving your work Many programs offer a feature that saves documents at regular intervals. Check your program’s documentation to see if it has an automatic save feature. Saving files Click on the arrow in the upper-left corner of your Windows and then click Save.
Page 101: Printing Your Work
File names The Windows contain up to 260 characters and can include spaces. Some applications do not support long file names and require file names limited to no more than eight characters. You may use all the letters, numbers, and other characters on the keyboard, except for these characters: \ / ? : * "...
Page 102: Backing Up Your Work
Learning the Basics Backing up your work Click on the arrow in the upper-left corner of your Windows and then click Print. The program displays a Print dialog box. (Sample Image) Print dialog box Specify the print parameters. For example, the range of pages and number of copies to print.
Page 103: Restoring Your Work
Restoring your work To restore information from your backup media to your internal storage drive, use the Restore option in the Windows Restore program. Look in the online Help or your operating system documentation for information on restoring files. (Sample Image) Backup and Restore screen TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the internal storage drive.
Page 104: Optical Drive Components
Learning the Basics Using the optical drive NOTE For optimum DVD performance, it is recommended that you play DVDs while running the computer on AC power. NOTE When viewing DVD movies use the DVD Player software that came with your computer. Optical drive components The optical drive is located on the side of the computer.
Page 105: Inserting An Optical Disc
Inserting an optical disc To insert an optical disc into the drive: Make sure the computer is turned on. The drive will not open if the computer’s power is off. Make sure the drive’s in-use indicator light is off. Press the drive’s eject button. The disc tray slides partially out of the drive.
Page 106: Playing An Audio Cd
If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
Page 107: Recording Optical Media
Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your Toshiba optical drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or optical media recorders.
Page 108: Removing A Disc With The Computer Off
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions and keep you up to date with future upgrades.
Page 109: Chapter 3: Mobile Computing
It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been preset by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you...
Page 110: Running The Computer On Battery Power
EasyGuard Optimize—to enable users to customize system settings to be more productive. *Toshiba EasyGuard some of which may or may not be available on a particular Toshiba computer depending on the model selected. See easyguard.toshiba.com Running the computer on battery power The computer contains a removable Lithium-Ion (Li-Ion) battery that provides power when you are away from an AC outlet.
Page 111: Power Management
Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact Toshiba’s Customer Support Center. Running the computer on battery power “Maintaining your battery”...
Page 112: Using Additional Batteries
Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Always use the battery charger specified by Toshiba. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com.
Page 113: Charging The Rtc Battery
The battery may not start charging immediately under the following conditions: ❖ The battery is extremely hot or cold. To ensure that the battery charges to its full capacity, wait until it reaches room temperature (50 to 80 degrees Fahrenheit, 10 to 26 degrees Celsius).
Page 114: Monitoring Main Battery Power
Mobile Computing Monitoring main battery power NOTE It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working.
Page 115: Determining Remaining Battery Power
HINT: Be careful not to confuse the battery light ( ON/OFF light ( When the ON/OFF light flashes amber, it indicates that the system is suspended (using the Windows Power button Wireless indicator light (Sample Illustration) Power and battery light locations Determining remaining battery power Wait at least 16 seconds after turning on the computer before trying NOTE...
Page 116: What To Do When The Main Battery Runs Low
Mobile Computing Monitoring main battery power Move the pointer over the power icon in the notification area, see “Finding your way around the desktop” on page 128 information on the notification area. A pop-up message displays the remaining battery power as a percentage. With repeated discharges and recharges, the battery’s capacity gradually decreases.
Page 117: Conserving Battery Power
To change the default notification settings: Click Start, Control Panel, System and Security, and then Power Options. The Power Options window appears. Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. Click Change advanced power settings. The Advanced settings tab of the Power Options window appears.
Page 118: Power Plans
Mobile Computing Monitoring main battery power There are various ways in which you can conserve power and extend the operating time of your battery: ❖ Enable Sleep or Hibernation, which saves power when you turn off the computer and turn it back on again ❖...
Page 119: Using A Hot Key To Set The Power Plan
To edit a plan or to edit advanced settings, continue to the following NOTE steps. Click Change plan settings to choose the plan you want to edit. This screen allows you to change basic settings. Click Change advanced power settings to access settings for battery notification levels, internal storage drive power save time, etc.
Page 120: Changing The Main Battery
Mobile Computing Changing the main battery Release the The hot key card disappears. You are now in the selected mode. Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object.
Page 121 Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock Slide the battery release latch to release the battery. Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
Page 122: Inserting A Charged Battery
Mobile Computing Changing the main battery Inserting a charged battery To insert a battery: Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. Insert the charged battery into the slot until the latch clicks. The battery pack has been designed so that you cannot install it with reverse polarity.
Page 123: Taking Care Of Your Battery
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries.
Page 124: Maintaining Your Battery
Mobile Computing Taking care of your battery Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
Page 125: Disposing Of Used Batteries
If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. In addition, Toshiba’s recycling initiatives include recycling programs, events and consumer promotions. For details, please visit www.laptops.toshiba.com/green.
Page 126: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cords, and compact discs.
Page 127: Chapter 4: Exploring Your Computer's Features
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your computer. Exploring the desktop The desktop is the launching pad for everything you can do in the ® Windows operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Page 128: Finding Your Way Around The Desktop
Exploring Your Computer’s Features Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, notification area, and background pattern. Icons Start button (Sample Image) Windows Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Page 129 Your desktop may contain other icons depending on your configuration. See Windows information on each icon and how to use it. Start button You use the Start button to: ❖ Start programs ❖ Open documents ❖ Adjust system settings ❖ Find files ❖...
Page 130: Setting Up For Communications
Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality using one of its communication ports. . For more information see ® networking problems, see 179. “Hot Keys/TOSHIBA Cards” on “Wireless will...
Page 131: Connecting A Modem To A Telephone Line
Accessing a network To access a network: ❖ At the office, connect an Ethernet cable to the Network port (RJ45) on your computer. For specific information about connecting to the network, consult your network administrator. ❖ Many hotels, airports, and offices offer Wi-Fi computer has Wi-Fi their Wi-Fi ❖...
Page 132 Exploring Your Computer’s Features Setting up for communications Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line.
Page 133: An Overview Of Using The Internet
An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Internet Service Providers ❖ Connecting to the Internet ❖...
Page 134: Connecting To The Internet
Exploring Your Computer’s Features An overview of using the Internet Connecting to the Internet To connect to the Internet, you need: ❖ A modem and telephone line, or a LAN connection ❖ A Web browser ❖ An Internet Service Provider (ISP) account Once you have established an ISP account, you can connect to the Internet.
Page 135: Uploading To, And Downloading Files From, The Internet
❖ Internet chat rooms A chat room is a Web site that offers a place where people with similar interests and ideas communicate in real-time, one-on- one or in groups, by typing messages which are instantly viewed by others on their computer screens. ❖...
Page 136: Exploring Audio Features
Exploring Your Computer’s Features Exploring audio features Exploring audio features You can use your computer to record sounds using the computer’s internal microphone (available on certain models) or an optional external microphone. You can listen to sound files or audio CDs using the built-in speakers, headphones, or external speakers.
Page 137: Using The Web Camera
The Web Camera software, by default, should already be running. The Web Camera indicator light glows when the Web Camera is active. For more information on the software, click Start, All Programs, TOSHIBA, Utilities, and then Web Camera Application Help. Exploring Your Computer’s Features...
Page 138: Using The Memory Card Reader
Exploring Your Computer’s Features Using the Memory card reader Using the Memory card reader The Memory card reader supports the use of Memory Stick Secure Digital These media can be used with a variety of digital products: digital music players, cellular phones, PDAs, digital cameras, digital video camcorders, etc.
Page 139: Removing Memory Media
Removing memory media Prepare the card for removal by clicking on the Show hidden icons button ( ), if necessary, in the notification area and then selecting the Safely Remove Hardware icon. If the system is unable to prepare the media for safe removal, a message will tell you to try again later.
Page 140: Chapter 5: Utilities
❖ TOSHIBA Assist ❖ TOSHIBA Application Installer ❖ Supervisor password ❖ User password ❖ TOSHIBA Face Recognition Utility ❖ TOSHIBA PC Diagnostic Tool Utility ❖ Mouse Utility ❖ TOSHIBA Hardware Setup ❖ TOSHIBA Zooming Utility ❖ TOSHIBA Accessibility...
Page 141: Toshiba Assist
TOSHIBA Service Station ❖ ConfigFree® TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, click Start, All Programs, TOSHIBA, Utilities, and then TOSHIBA Assist.
Page 142: Connect
Utilities TOSHIBA Assist Connect The feature available in this category is ConfigFree Doctor. (Sample Image) TOSHIBA Assist window – Connect tab ® Connectivity...
Page 143: Secure
Secure The features available in this category are: ❖ Supervisor password ❖ User password (Sample Image) TOSHIBA Assist window – Secure tab Utilities TOSHIBA Assist...
Page 144: Protect & Fix
Utilities TOSHIBA Assist Protect & Fix The feature available in this category is Tool Utility. (Sample Image) TOSHIBA Assist window – Protect & Fix tab TOSHIBA PC Diagnostic...
Page 145: Optimize
Optimize The features available in this category are: ❖ Mouse Utility ❖ TOSHIBA Accessibility ❖ TOSHIBA Zooming Utility ❖ TOSHIBA Hardware Setup ❖ TOSHIBA Face Recognition Utility (Sample Image) TOSHIBA Assist window – Optimize tab Utilities TOSHIBA Assist (Hardware Settings)
Page 146: Toshiba Application Installer
Utilities TOSHIBA Application Installer TOSHIBA Application Installer The TOSHIBA Application Installer allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications: Click Start, All Programs, My Toshiba, and then TOSHIBA Application Installer.
Page 147: Setting Passwords
When you set a password, you must enter the password before you can work on your computer again. Toshiba supports several types of passwords on your computer: ❖ An instant password—Secures your open programs and files when leaving the computer temporarily.
Page 148: Using A Supervisor Password
Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your computer.
Page 149: Using A User Password
Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your computer.
Page 150: Deleting A User Password
Utilities Setting passwords To register a password for the power-on password functions: Click Start, All Programs, TOSHIBA, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears. On the left side, click the Secure tab. Click the User Password icon.
Page 151: Toshiba Face Recognition Utility
Toshiba does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the face recognition software or utility.
Page 152: Toshiba Pc Diagnostic Tool Utility
Refer to the online Help documentation within the application for additional help. NOTE The TOSHIBA PC Diagnostic Tool utility may show tests for features you do not have. This is normal and does not indicate a problem. To use the TOSHIBA PC Diagnostic Tool utility:...
Page 153: Mouse Utility
The settings you can change are divided into these categories: ❖ Buttons ❖ Pointers ❖ Pointer Options ❖ Wheel ❖ Hardware ❖ Device Settings You may see additional categories depending on your particular pointing device. Adjust the settings as desired, then click OK. Utilities Mouse Utility TOSHIBA Assist.
Page 154: Toshiba Hardware Setup
To access it: ❖ Click Start, All Programs, TOSHIBA, Utilities, and then HWSetup, or click the TOSHIBA Hardware Settings icon in the Optimize tab of The TOSHIBA HWSetup screen appears. (Sample Image) TOSHIBA HWSetup screen – General tab options The TOSHIBA HWSetup screen may have the following tabs: ❖...
Page 155 ❖ LAN—Allows you to set networking functions ❖ Password—Allows you to set a user password ❖ USB—Allows you to enable or disable USB Legacy Emulation TOSHIBA Hardware Setup key. . For more information, see Fn + F5 Utilities “Directing the...
Page 156: Toshiba Zooming Utility
Acrobat ❖ Icons on the desktop To access the TOSHIBA Zooming Utility: Click Start, All Programs, TOSHIBA, Utilities, and then Zooming Utility. The TOSHIBA Zooming Utility Properties screen appears. (Sample Image) TOSHIBA Zooming Utility Properties screen Select the desired option(s).
Page 157: Toshiba Accessibility
TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the press it once, release it, and then press a function key to activate the hot key function.
Page 158: Toshiba Service Station
Utilities TOSHIBA Service Station TOSHIBA Service Station The TOSHIBA Service Station helps you keep your new computer running at its best by notifying you when updated software, firmware, documentation or other information is available for your computer. The TOSHIBA Service Station will alert you when updates are available, and you can then choose to install the updates if you wish.
Page 159: Configfree ® Utilities
❖ Double-click the ConfigFree icon ❖ Click the ConfigFree icon then click the desired utility. NOTE If your computer is not connected to a network, the ConfigFree icon in the notification area is displayed with an “X.” ® ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network connection problems.
Page 160 Utilities ConfigFree® Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree network settings and devices. You can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally, for example, you can set up a profile to match that environment and connect to the network.
Page 161 Click Open Settings. The ConfigFree Profile Settings window appears. (Sample Image) ConfigFree Profile Settings window Click Add to start the Create Profile Wizard. Utilities ConfigFree®...
Page 162: Chapter 6: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
Page 163: Problems When You Turn On The Computer
Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working.
Page 164 If Something Goes Wrong Problems when you turn on the computer The computer starts but when you press a key nothing happens. Verify that the active program accepts text input. Try clicking your mouse on an area where you can type text and try typing again. Your computer may be in Sleep mode and have a software or resource conflict.
Page 165 “trickle-charge” to the battery. Once the battery has been trickle-charged, it may begin working correctly again. If the trickle-charging does not prove effective, visit the Toshiba Web site at Bulletin Step-Charging the computer’s battery (click the ® Ask Iris link and search for the support bulletin by name).
Page 166: The Windows Operating System Is Not Working
The output specifications of the AC adapter must match the input specifications of the computer. If the specifications do not match, locate and use the AC adapter that shipped with your computer. If the specifications do match, contact Toshiba. See page 186. ®...
Page 167: Using Startup Options To Fix Problems
The Windows Using Startup options to fix problems If the operating system fails to start properly, you may have to change your system’s configuration or verify the startup procedure to fix the problem. To do this, use the options in the Startup menu. To open the Startup menu: Restart your computer.
Page 168: Internet Problems
Click one of the options listed in the window and then follow the on-screen instructions. You can connect to Support Online by clicking the Ask button and then clicking the Microsoft Customer Support or by going to Toshiba support at pcsupport.toshiba.com. ® operating system is not working ®...
Page 169: Fixing A Problem With Device Manager
Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable. Device Manager is a configuration tool for advanced users who understand configuration parameters and the ramifications of changing them.
Page 170: Memory Problems
If Something Goes Wrong Memory problems Memory problems Incorrectly connected or faulty memory modules may cause errors that seem to be hardware or even software related. It is worthwhile checking for these first: Click Start, and then click the Shut down button in the lower-right corner of the Start menu.
Page 171 Here are some typical problems and how to solve them: The AC power light does not come on when you plug in the AC adaptor and power cord/cable. Make sure the AC adaptor and power cord/cable are firmly plugged into both the wall outlet and the computer. If the AC power light still does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance.
Page 172: Keyboard Problems
After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries. To purchase a new battery pack, see your accessories information included with your computer, or visit the Toshiba Web site at accessories.toshiba.com.
Page 173 If you are using the built-in screen, make sure the display priority is not set for an external monitor. To do this, press simultaneously (once). If this does not correct the problem, press simultaneously again to return the display priority to its previous setting.
Page 174: Disk Or Storage Drive Problems
If Something Goes Wrong Disk or storage drive problems The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode, and not simultaneous mode.
Page 175 NOTE This feature is not available for optical drives. Click the Tools tab. Click the Check now... button. The Check Disk box appears. You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors Click Start.
Page 176: Optical Drive Problems
Some discs run correctly but others do not. Check that the type of disc you are using is compatible with your optical drive. For more information regarding supported optical media formats, refer to the complete detail specifications for your computer at pcsupport.toshiba.com. 174). “Disk or...
Page 177: Sound System Problems
If the problem is with an optical data disc, refer to the software’s documentation and check that the hardware configuration meets the program’s needs. The disc will not come out of the drive when you click the eject button on the screen. Press the button on the optical drive itself.
Page 178: Modem Problems
Make sure the line has a dial tone. Connect a telephone handset to the line to check this. The other system may be busy or off line. Try making a test transmission to someone else. For more information regarding your system’s V.92 modem, visit the Toshiba Web site at pcsupport.toshiba.com.
Page 179: Wireless Networking Problems
® adapter. ® Control Panel's Device Manager to verify ® adapter is recognized by the Windows . For more information see in the Search programs and files field. ® ) networking. ® “Hot Keys/TOSHIBA Cards” on ®...
Page 180: Dvd Operating Problems
If Something Goes Wrong DVD operating problems Enter The IP address for each active network adapter will be displayed. ❖ Connect your computer directly to your router or broadband modem, by plugging a standard CAT5 Ethernet patch cable (sold separately) into your computer's RJ45 Ethernet port. If your connection problem disappears, the problem lies in the ®...
Page 181: Develop Good Computing Habits
“Checking device properties” on page 169 on using Device Manager to view the optical drive properties. Check the Toshiba Web site for new information on optical drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
Page 182: Data And System Configuration Backup In The Windows Operating System
If Something Goes Wrong Develop good computing habits Some people use a combination of these methods, backing up all files to tape weekly and copying critical files to diskette on a daily basis. If you have installed your own programs, you should back up these programs as well as your data files.
Page 183 Follow these steps to create a restore point using the System Restore utility: Click Start, Control Panel, System and Security, and then System. In the left pane, click System protection. The System Protection tab of the System Properties window appears. Click Create...
Page 184 An external hard drive is recommended in case the internal storage drive fails. No additional software is required. Most of the optical drives built into recent Toshiba portable computer models can write to (or ‘burn’) as well as read from optical discs.
Page 185 then be able to easily restore the Windows the state it was in prior to the installation, undoing any changes that the installation process introduced. ❖ Back up your critical data (see entire computer with the Windows® operating system” on page 184).
Page 186: If You Need Further Assistance
Toshiba’s Technical Support Web site For technical support, or to stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com Toshiba voice contact Before calling Toshiba, make sure you have: ❖...
Page 187: Other Toshiba Internet Web Sites
Information about what you were doing when the problem occurred ❖ Exact error messages and when they occurred For technical support, call the Toshiba Customer Support Center: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Other Toshiba Internet Web sites toshiba.com...
Page 188 Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm. Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec.
Page 189: Appendix A: Hot Keys/Toshiba Cards
Appendix A Hot Keys/TOSHIBA Cards Hot keys and TOSHIBA Cards provide a quick way to modify selected system functions and to launch applications. There are two types of TOSHIBA Cards: Hot Key Cards and Application Cards. Hot Key Cards The Hot Key Cards are used to set or modify the following system functions: ❖...
Page 190: Using The Hot Key Cards
To use the Hot Key Cards: Press and hold the The TOSHIBA Cards appear along the top of the screen. (Sample Image) Hot Key Card display Click the Card for the system function to be modified.
Page 191: Application Cards
158. TOSHIBA Zooming utility For more information, refer to Zooming Utility” on page Disc Creator utility This Application Card launches the TOSHIBA Disc Creator utility. TOSHIBA Hardware Setup utility For more information, refer to Hardware Setup” on page “TOSHIBA Assist”...
Page 192: Using The Application Cards
Using the Application Cards To launch an application using the Application Cards: Press and hold the The TOSHIBA Cards display at the top of the screen. (Sample Image) TOSHIBA Card display Click the “stacked” card on the far right of the display. The Application Cards are hidden under this card.
Page 193: Hot Key Functions
Hot keys have a legend on the key indicating the option or feature the key controls. Volume Mute This TOSHIBA Card or hot key enables/disables volume mute on your computer. When volume mute is enabled, no sound will come from the speakers or headphones.
Page 194: Lock (Instant Security)
Hot Keys/TOSHIBA Cards Hot key functions Lock (Instant security) This TOSHIBA Card or hot key blanks the display. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Security options ❖ ❖ hot key function activates instant security. The user...
Page 195: Power Plan
Hot Keys/TOSHIBA Cards Hot key functions Power plan This TOSHIBA Card or hot key displays the power plans and cycles through the power plans. The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options window.
Page 196: Sleep Mode
Hot Keys/TOSHIBA Cards Hot key functions Sleep mode This TOSHIBA Card or hot key places the computer into Sleep mode. For more information about Sleep mode, please see and configuring Sleep mode” on page Selecting this Card or pressing the hot key displays the...
Page 197: Hibernation Mode
Hibernation mode This TOSHIBA Card or hot key places the computer into Hibernation mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page Selecting this Card or pressing the hot key displays the...
Page 198: Output (Display Switch)
Hot Keys/TOSHIBA Cards Hot key functions Output (Display switch) This TOSHIBA Card or hot key cycles through the power- on display options (only the first option is available when you do not have an external monitor attached) (the last option is available only if you are in Extended Display Mode).
Page 199: Display Brightness
To swap sides, select Swap Image Display. Display brightness This TOSHIBA Card decreases or increases the screen brightness. This hot key decreases the screen brightness. This hot key increases the screen brightness.
Page 200: Disabling Or Enabling Wireless Devices
Hot Keys/TOSHIBA Cards Hot key functions Disabling or enabling wireless devices This TOSHIBA Card or hot key enables/disables the optional wireless devices installed in your computer. The wireless modes are: ❖ Selecting this Card or pressing the hot key displays the...
Page 201: Disabling Or Enabling The Touchpad
Disabling or enabling the TouchPad™ This TOSHIBA Card or hot key enables/disables the TouchPad™. For more information on using the TouchPad, see the TouchPad™” on page Selecting this Card or pressing the hot key displays the following options: (Sample Image) Disable or Enable TouchPad options ❖...
Page 202: Zoom (Display Resolution)
Hot Keys/TOSHIBA Cards Hot key functions Zoom (Display resolution) This TOSHIBA Card or hot key switches screen resolution. Selecting this Card or pressing the hot key displays the following options: [Space bar] (Sample Image) Screen resolution options Cycle through the screen resolutions, then select the desired...
Page 203: Keyboard Hot Key Functions
This hot key turns the numeric overlay on and off. This hot key turns the scroll lock feature on and off. This hot key turns the TOSHIBA Zooming Utility to zoom out. This hot key turns the TOSHIBA Zooming Utility to zoom in.
Page 204: Appendix B: Power Cord/Cable Connectors
Appendix B Power Cord/Cable Connectors Your computer ships with the correct power supply for the country of purchase. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. UL approved United Kingdom BS approved Australia AS approved...
Page 205: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 DIMM alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 206 Glossary DSTN DVD-ROM digital versatile (or video) disc read-only memory EPROM eSATA HDMI HDMI-CEC HTML IEEE LPT1 MIDI PCMCIA disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory external Serial Advanced Technology Attachment file allocation table Federal Communications Commission...
Page 207 SCSI SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 208 Glossary application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. backup — A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged.
Page 209 CD — An individual compact disc. See also CD-ROM. CD-ROM (compact disc read-only memory) — A form of high- capacity storage that uses laser optics instead of magnetic means for reading data. See also CD. Compare DVD-ROM. central processing unit (CPU) — The chip that functions as the “brain” of the computer.
Page 210 Glossary cursor — An on-screen symbol (usually a flashing vertical line) that indicates the position where characters will appear when you enter data. default — The setting selected by a program when the user does not specify an alternative setting. device —...
Page 211 document — Any file created with an application and, if saved to disk, given a name by which it can be retrieved. See also file. double-click — To press and release the pointing device’s primary button rapidly twice without moving the pointing device. In the Windows button, unless otherwise stated.
Page 212 Glossary file — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also document. file allocation table (FAT) — The section of a storage drive that keeps track of the location of stored files.
Page 213 Hibernation — A feature of many Toshiba computers that saves to the internal storage drive the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 214 Glossary liquid crystal display (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it.
Page 215 network — A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail. non-interlaced — A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen.
Page 216 Glossary Plug and Play — Generally, refers to the computer’s ability to automatically configure itself to work with peripheral devices. When capitalized, refers to a standard that, when followed by a device manufacturer, allows a computer to configure itself automatically to work with the device. pointer —...
Page 217 restart — Synonymous with reboot. To reset the computer by reloading the operating system without turning the computer off. See also boot. RJ11 — A modular connector used on most U.S. telephone systems and direct-connect modems. The RJ11 connector is a 6-wire connector. ROM (read-only memory) —...
Page 218 Glossary system prompt — The symbol (in the MS-DOS generally a drive letter followed by a “greater than” sign) indicating where users are to enter commands. TFT display — See active-matrix display. universal serial bus (USB) — USB is a serial bus that supports a data transfer rate of up to 480 Mbps (480 million bits per second).
Page 219: Index
116 power plan 195 power plan hot key 119 real-time clock (RTC) 111 remaining power 115 removing 120 safety precautions 123 BIOS Setup see TOSHIBA Hardware Setup button power 50 start 129 buttons eject, optical drive 104 Call2Recycle™ battery 126...
Page 220 Index network connection 131 set up 130 computer caring for 91 cleaning 91 moving 92 non-system disk or disk error message 165 not accessing disk drives 164 running on battery power 110 setting up 45 warning resume failure message computer lock 92 computing tips 93 ConfigFree®...
Page 221 not working 174 mouse 79 external display device RGB port 77 external display, adjusting 79 FAT (File Allocation Table) 174 file extensions 101 file, backing up 94 files backing up 102 printing 101 restoring 103 saving 99 Fn keys 95 function keys 95 HDMI™...
Page 222 Index troubleshooting 172 unexpected characters 172 using 94 keyboard, external 79 keyboard, full-size 95 light AC power 46 drive in-use indicator 104 lock computer, using 92 main battery changing 120 installing 120 removing 120 safety precautions 123 manual eject hole optical drive 104 memory adding 52...
Page 223 175 cannot read a diskette 176 changing display properties 173 checking device properties 169 computer will not power up 163 contacting Toshiba 186 corrupted/damaged data files 175 Device Manager 169 disk drive is slow 175 display is blank 172...
Page 224 TOSHIBA Application Installer 146 TOSHIBA Assist 141 Toshiba EasyGuard® 110 TOSHIBA Face Recognition Utility TOSHIBA Hardware Setup 154 Toshiba online resources 108 TOSHIBA PC Diagnostic Tool Utility TOSHIBA Service Station 158 TOSHIBA Zooming Utility 156 TouchPad™ adjusting settings 76 disabling 76...
Page 225 keyboard 172 optical drive 176 turning on the computer 50 turning on the power 50 USB-compatible printer 80 user password, disabling 150 user password, setting 149 using a file extension 101 Utilities 140 video cables 77 video display device connecting 77 video projector adjusting display 79 warranty...

This manual is also suitable for:

L450-sp2918a L450-sp2918c L450-ez1522 L450-sp2918r L450-w1542 L450-w1543 ... Show all

Toshiba L450-EZ1510 User Manual

Chapter 1: Getting Started

Chapter 2: Learning the Basics

Chapter 3: Mobile Computing

Chapter 4: Exploring Your Computer's Features

Chapter 5: Utilities

Chapter 6: If Something Goes Wrong

Appendix A: Hot Keys/Toshiba Cards

Appendix B: Power Cord/Cable Connectors

Quick Links

Related Manuals for Toshiba L450-EZ1510

Summary of Contents for Toshiba L450-EZ1510