Auto White Balance Check - Sony DSC-P1 Service Manual And Parts List
Hide thumbs
Also See for DSC-P1:
- Operating instructions manual (72 pages) ,
- Service manual (105 pages)
Table of Contents
Advertisement
13. Auto White Balance Check
Mode
Subject
Measurement Point
Measuring Instrument
Specified Value
Note 1: Refer to "Picture Frame Setting" for XH, XL, YH and
Note 2: The right four digits of the page: 1 displayed data of the
Checking method:
Order Page Address Data
1
2
3
4
5
6
7
8
9
10
11
12
13
INDOOR data check
14
15
16
17
18
19
20
INDOOR luminance point check
21
22
Downloaded from
www.Manualslib.com
STILL
Clear chart
(Color reproduction adjustment
frame)
Displayed data of Video terminal
of Page: 1 (Note 2) A/V OUT jack
Adjustment remote Vectorscope
commander
R ratio:
3E00 to 4200
B ratio:
3E00 to 4200
YL.
adjusting remote commander.
1:XX:XX
Displayed data
Procedure
Check that the lens is not
covered with either filter.
0
01
01
5
F1
FF
D
63
40
Press PAUSE button.
Perform "Data setting during
camera system adjustment".
(Refer to page 5-13)
6
90
00
6
91
04
6
92
00
6
93
30
6
6C
01
6
2C
01
6
01
79
Press PAUSE button.
Wait for 3 seconds.
E
52
Note down the data.
E
52
1A
Press PAUSE button.
6
01
0F
Press PAUSE button.
0
03
04
Check that the displayed data
1
(Note 2) satisfied the R ratio
specified value.
0
03
05
Check that the displayed data
1
(Note 2) satisfied the B ratio
specified value.
0
03
00
Check that the center of the
white luminance point within
the circle shown Fig 5-1-19 (A).
manuals search engine
OUTDOOR luminance point check
23
24
25
26
(75 Ω terminated)
27
28
Fig. 5-1-19
29
(A) and (B)
30
31
32
33
34
35
Processing after Completing Adjustment:
Order Page Address Data
1
2
3
4
5
6
7
8
9
5-23
Place the C14 filter on the lens.
E
4B
Note down the data.
E
4B
20
Press PAUSE button.
6
01
3F
Press PAUSE button.
Check that the center of the
white luminance point settles
in the circle shown Fig 5-1-19
(B).
6
90
XL
(Note 1)
6
91
XH
(Note 1)
6
92
YL
(Note 1)
6
93
YH
(Note 1)
6
6C
01
6
2C
01
6
01
79
Press PAUSE button.
Wait for 3 seconds.
Procedure
6
01
00
Press PAUSE button.
6
6C
00
Set data noted down at step 24,
E
4B
and press PAUSE button.
Set data noted down at step 14,
E
52
and press PAUSE button.
6
2C
00
5
F1
00
D
63
00
Press PAUSE button.
Release the data setting
performed at step 5.
(Refer to page 5-13)
0
01
00
R-Y
4 mm
4 mm
Fig. 5-1-19 (A)
R-Y
1 mm
1.5 mm
6 mm
6 mm
Fig. 5-1-19 (B)
B-Y
B-Y
Advertisement
Table of Contents
