hit counter script
Toshiba Libretto U100 User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. libretto U100 Series
  6. User manual

Toshiba Libretto U100 User Manual

Toshiba libretto u100 portable personal computer user's manual
Hide thumbs Also See for Libretto U100:
Table of Contents

Advertisement

Quick Links

See also: Maintenance Manual
libretto U100
TOSHIBA
libretto U100
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Libretto U100

Summary of Contents for Toshiba Libretto U100

  • Page 1 U100 TOSHIBA libretto U100 Portable Personal Computer User’s Manual...
  • Page 2 This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA libretto U100 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
  • Page 3 Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s Mini-RGB port, USB port, i.LINK (IEEE1394)
  • Page 4 User’s Manual Telephone: (949) 583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: PLU10* conforms to the following Standards: Supplementary “The product complies with the Information: requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.”...

  • Page 5: Region Selection

    User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04...
  • Page 6 User’s Manual One of the labels is located on the module. Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the modem ■...

  • Page 7: Type Of Service

    FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
  • Page 8 User’s Manual Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
  • Page 9 User’s Manual Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
  • Page 10 User’s Manual ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and b/ The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the...

  • Page 11: General Conditions

    User’s Manual ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.

  • Page 12: Optical Disc Drive Safety Instructions

    User’s Manual Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD-ROM&CD-R/RW UJDA765 ■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
  • Page 13 User’s Manual DVD Super Multi UJ-822 ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 14 User’s Manual International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 15 User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
  • Page 16 User’s Manual User’s Manual...

  • Page 17: Table Of Contents

    U100 Table of Contents Preface Manual contents ......... .xxv Conventions.
  • Page 18 Operating Basics TOSHIBA Pointing Device ........4-1 Using the AccuPoint .
  • Page 19 DLA for TOSHIBA ........
  • Page 20 Using the Hard Disk Drive (HDD) Protection ....4-39 TOSHIBA HDD Protection Properties ..... . . 4-40 Detail Properties .
  • Page 21 Replacing the battery pack....... . . 6-11 TOSHIBA Password Utility ....... . . 6-13 User password.
  • Page 22 TOSHIBA support ........

  • Page 23: Appendix B Display Controller And Modes

    Table of Contents Non-applicable Icons*5........10-2 Wireless LAN/Atheros*6 .
  • Page 24 Table of Contents xxiv User’s Manual...

  • Page 25: Manual Contents

    This manual tells how to set up and begin using your libretto U100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

  • Page 26: Conventions

    Preface Chapter 4, Operating Basics, includes instructions on using the following devices: Pointing Device, Fingerprint Sensor, USB floppy disk drive, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/ DVDs.

  • Page 27: Key Operation

    Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, CTRL + C means you must hold down CTRL and at the same time press C.
  • Page 28 Preface xxviii User’s Manual...

  • Page 29: General Precautions

    U100 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 30: Pc Card Overheating

    General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phones can interfere with the audio system.

  • Page 31: Introduction

    Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.

  • Page 32: Software

    The following software is preinstalled: ■ ® Microsoft Windows XP Professional ■ Microsoft Internet Explorer ■ TOSHIBA Utilities ■ TOSHIBA SD Memory Boot Utility ■ DVD Video Player ■ TOSHIBA Power Saver ■ TOSHIBA Assist ■ TOSHIBA ConfigFree ■ TOSHIBA Zooming Utility ■...

  • Page 33: Documentation

    If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and...
  • Page 34 For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under “Environmental Conditions” in your PC documentation. Contact Toshiba technical service and support, refer to TOSHIBA support section in Chapter 9 Troubleshooting for more information.
  • Page 35 Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
  • Page 36 Introduction libretto DVD Dock ■ The optical media drive is optional. ■ The optical media drive can be used by connecting libretto DVD Dock to this computer. DVD-ROM&CD-R/RW Some models are equipped with a full-size, DVD- drive ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor.
  • Page 37 Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in*1 7.2” TFT LCD screen 16 M colors, with a resolution of 1280 horizontal × 768 vertical pixels WXGA.
  • Page 38 Introduction Universal Serial Bus The computer has Universal Serial Bus ports that (USB 2.0) comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard (The ports also support USB 1.1). Docking port This port enables connection of an optional libretto DVD Dock described in the Options...

  • Page 39: Appendix E

    Introduction Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line.
  • Page 40 Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision B or G), and Turbo Mode.

  • Page 41: Special Features

    Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot keys Key combinations let you quickly change the system configuration directly from the keyboard without running a system configuration program.
  • Page 42 LCD display panel is opened. You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver. Low battery When battery power is exhausted to the point that...

  • Page 43: Utilities

    “shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Fn-esse. DVD Video Player The DVD Video Player is used to play DVD- Video.
  • Page 44 Bluetooth cannot be used in models that do not have a Bluetooth module installed. TOSHIBA SD The TOSHIBA SD memory boot utility is a utility Memory Boot Utility which can create SD memory card to a boot disk. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows.
  • Page 45 For other sound settings, use the Windows Device Manager, Multimedia Panel or Volume Dial. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks.

  • Page 46: Options

    333) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. AC adaptor If you use your computer at more than one site...
  • Page 47 A mobile external hard disk drive that is compatible with USB2.0. Data can be read and written by connecting to the USB port of the computer. You can buy the module from TOSHIBA dealer. DVD-ROM&CD-R/RW DVD-ROM&CD-R/RW drive is available as an drive optional external optical disk drive.
  • Page 48 Introduction 1-18 User’s Manual...

  • Page 49: The Grand Tour

    U100 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer.*5 Disclaimer (Non-applicatable Icons) Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not...

  • Page 50: Left Side

    The Grand Tour PC card eject lever This is a lever for taking out PC card from a PC card slot. i.LINK (IEEE1394) Connect an external device, such as a digital port video camera to this port for high-speed data transfer.

  • Page 51: Right Side

    The Grand Tour ■ Turn WiFi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any WiFi or Bluetooth functionality.
  • Page 52 The Grand Tour Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones. Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.

  • Page 53: Back Side

    The Grand Tour LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). Refer to Chapter 4, Operating Basics, for details.

  • Page 54: Underside

    The Grand Tour Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Notches Battery lock Battery release latch Docking port Memory module cover Figure 2-5 The underside of the computer Battery lock Slide this lock to release the battery pack for removal.

  • Page 55: Front With The Display Open

    The Grand Tour Notches Notches on the computer engage hooks on the libretto DVD Dock to hold the connection securely. Memory module This cover protects one memory module socket, cover one module is preinstalled. Refer to the Memory expansion section in Chapter 8, Optional Devices.
  • Page 56 Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Special features, for details on settings.

  • Page 57: System Indicators

    The Grand Tour Fingerprint Sensor Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a security- enabled homepage through IE (Internet Explorer). ■ Files and folders can be encrypted/decrypted and third party access to them prevented.

  • Page 58: Usb Floppy Disk Drive

    The Grand Tour Wireless The Wireless communication indicator glows communication when the Wireless LAN and Bluetooth functions are turned on. Some models are equipped with a Wireless communication. USB floppy disk drive USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks.

  • Page 59: Optical Media Drives

    The Grand Tour Optical media drives ■ The optical media drive is optional. ■ The optical media drive can be used by connecting libretto DVD Dock to this computer. One of the following optical media drives is installed in the computer: DVD- ROM&CD-R/RW and DVD Super Multi drives.

  • Page 60: Writable Discs

    The Grand Tour Writable discs This section describes the types of writable CD/DVD discs. Check the specifications for your drive to for the type of discs it can write. Use RecordNow! to write compact discs. Refer to Chapter 4, Operating Basics.

  • Page 61: Dvd Super Multi Drive

    The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
  • Page 62 For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC.

  • Page 63: Getting Started

    U100 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 64: General Conditions

    PC, it could cause a system failure, malfunction or loss of data. If dust contaminates the PC, do not turn on the power. Take it to an authorized Toshiba service provider before you use it. ■ Never place your PC near an object that generates a magnetic field, such as a speaker or TV.

  • Page 65: Placement Of The Computer

    Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location.

  • Page 66: Seating And Posture

    Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Figure 3-1 Posture and positioning of the computer ■...

  • Page 67: Work Habits

    Getting Started Consider the following suggestions regarding lighting your work environment: ■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user. ■...

  • Page 68: Other Things To Note

    Power and Power-Up Modes. ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury.
  • Page 69 Getting Started ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region. ■...

  • Page 70: Opening The Display

    Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the left of the computer. DC IN 15V jack Figure 3-4 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.

  • Page 71: Turning On The Power

    Getting Started Turning on the power This section describes how to turn on the power. The Power LED indicates the status. Refer to the Power indicator section in Chapter 6, Power and Power-Up Modes. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system.

  • Page 72: Shut Down Mode (Boot Mode)

    Getting Started Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1. If you have entered data, save it to the hard disk or to a floppy disk. 2.
  • Page 73 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.

  • Page 74: Standby Mode

    ■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.

  • Page 75: Restarting The Computer

    1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.

  • Page 76: Creating The Optical Recovery Discs

    Please verify your Optical Drive supports the blank media you choose. 3. Turn on your computer to open Windows XP. RecordNow! Basic for TOSHIBA is required to create the Recovery Discs. Other disc writing software is not supported. 3-14...

  • Page 77: Restoring The Preinstalled Software From The Recovery Hdd

    Getting Started 4. Insert the (first) blank media into the tray of the Optical Drive. 5. Double click the Recovery Disc Creator Launcher icon on the Windows XP desktop, or Select the application from start Menu. 6. After Recovery Disc Creator starts, select the type of media and the title you wish to copy to the media then click the Burn button.

  • Page 78: Restoring The Preinstalled Software From Your Creating Recovery Media

    2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.

  • Page 79: Operating Basics

    Operating Basics This chapter gives information on basic operations including using the TOSHIBA Pointing Device, the Fingerprint Sensor, the USB floppy disk drive, optical media drives, Sound System, Modem, Wireless communication features, LAN and Hard Disk Drive (HDD) protection. It also provides tips on care of the computer, floppy disks and CD/DVDs.

  • Page 80: Using The Accupoint

    Operating Basics Using the AccuPoint To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer. Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad. Two buttons below the AccuPoint are used like the buttons on a mouse pointer.

  • Page 81: Replacing The Cap

    Operating Basics Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with the computer. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight Figure 4-2 Removing the AccuPoint cap 2.

  • Page 82: Points To Note About The Fingerprint Sensor

    Operating Basics Points to note about the Fingerprint Sensor Failure to follow these guidelines might result in (1) damage to the sensor or cause sensor failure, (2) finger recognition problems, or lower finger recognition success rate. ■ Do not scratch or poke the sensor with your nails or any hard or sharp objects.

  • Page 83: Points To Note About The Fingerprint Utility

    Toshiba does not guarantee that the fingerprint sensor will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.

  • Page 84: Set Up Procedure

    Operating Basics In the help file, it is stated that this software's Password Replacement function can be used for the Internet and general applications. However, the Internet Password Replacement function in the fingerprint utility provided in this computer can only be used with IE (Internet Explorer). There is a section on Strong Logon Security in the help file, but the function is not available in the fingerprint utility provided in this computer.

  • Page 85: Window Logon Via Fingerprint Authentication

    Operating Basics We recommend first-timers to click Practice, and then swipe the finger as a practice. 5. The Capture Fingerprint screen is displayed. Follow the onscreen instructions and use the same finger you have selected under Choose Finger to swipe three times to allow the sensor to read the fingerprint. The fingerprint will be shown in green if properly read, or in red if the reading is abnormal.

  • Page 86: How The Swipe The Finger

    The screen can be scrolled up or down by sliding the finger over the Fingerprint Sensor. 3. Click (Double-click:) : TOSHIBA Quick Launcher will start up when the Fingerprint Sensor is double-clicked using the finger. 4. Click (Tap once) : TOSHIBA Quick Launcher items can be selected by clicking on the Fingerprint Sensor with the finger.

  • Page 87: Connecting Usb Floppy Disk Drive

    Operating Basics Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Refer to Figure 4-3. Make sure the connector is right side up and properly aligned with the socket.

  • Page 88: Using Optical Media Drives

    Operating Basics Using optical media drives ■ The optical media drive is optional. ■ The optical media drive can be used by connecting libretto DVD Dock to this computer. ■ Please ensure that it is used on a flat surface such as a table when a CD/DVD is used to connect to the libretto DVD Dock.

  • Page 89: Loading Discs

    Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-4 to 4-7. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject button Figure 4-4 Pressing the eject button 2.
  • Page 90 Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-6 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray.

  • Page 91: Removing Discs

    Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. ■ Always keep fingers away from the sides of the tray when closing the tray of an optical drive (CD/DVD drive, CD-RW drive, Multi-drive or equivalent drive) to avoid pinching your fingers.

  • Page 92: How To Remove Cd/Dvd When The Disk Tray Will Not Open

    Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Figure 4-8 Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place.

  • Page 93: Writing Cds On Dvd-Rom&Cd-R/Rw Drive

    Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs.

  • Page 94: When Writing Or Rewriting

    Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used.

  • Page 95: Writing Cd/Dvds On Dvd Super Multi Drive

    DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product.

  • Page 96: Before Writing Or Rewriting

    Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
  • Page 97 Operating Basics DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0 or Version Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM).

  • Page 98: When Writing Or Rewriting

    Operating Basics ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver, which can put a heavy load on the CPU. ■ Operate the computer in the full-power mode. Do not use power-saving features.

  • Page 99: Recordnow! Basic For Toshiba

    Operating Basics RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!. ■ You cannot use RecordNow!'s “Audio CD for Car or Home CD Player”...

  • Page 100: Data Verification

    3. Mark the Verify data written to the disc after burning check box in the Data Options. 4. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).

  • Page 101: How To Make A Dvd-Video

    Operating Basics 4. Click the Advanced tab in the System Properties window. 5. Click the Settings icon in the "Performance" section. 6. Click the Advanced tab in the Performance Options window. 7. Click the Change icon in the "virtual memory" section. 8.
  • Page 102 Operating Basics ■ Do not change display settings while using WinDVD Creator. ■ Do not enter standby/hibernation mode while using WinDVD Creator. ■ Do not operate WinDVD Creator immediately after turning on the computer. Please wait until all Disc Drive activity has stopped. ■...

  • Page 103: Media Care

    Operating Basics 3. About Disc Manager ■ WinDVD Creator can edit one play list on a disc. ■ WinDVD Creator might show a different a thumbnail than you previously set in CE (Consumer Electronics) DVD-RAM recorder. ■ Using the Disc Manager, you can edit DVD-VR format on DVD- RAM, DVD+VR format on DVD+RW, and DVD-Video format on DVD-RW.

  • Page 104: Floppy Disks

    Operating Basics Floppy disks 1. Store your floppy disks in the container they came in to protect them and keep them clean. If a floppy disk is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2.

  • Page 105: Soundmax Control Panel

    CD by the analog CD audio. Virtual Sound TOSHIBA Virtual Sound works as an audio filter using SRS WOW XT and SRS TruSurround XT functions provided by SRS Labs, Inc. in United States.

  • Page 106: Modem

    Check the specified areas carefully before using it. To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 107: Properties Menu

    Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system.

  • Page 108: Attaching The Ferrite Core To The Modular Cable

    Operating Basics Attaching the ferrite core to the modular cable The ferrite core that attaches to the modular cable bundled with this product is explained here. When connecting the modular cable, attaching the bundled ferrite core to the modular cable will help to reduce noise. To attach the ferrite core, follow the steps below.

  • Page 109: Connecting

    Operating Basics 3. Wind the modular cable around the ferrite core as in the diagram shown below. Wind the modular cable loosely one full round around the ferrite core. Please do not forcibly pull the modular cable when winding. Modular cable Figure 4-12 Furling the modular cable 4.

  • Page 110: Disconnecting

    Operating Basics ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■...

  • Page 111: Wireless Communications

    Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. All models are provided with Wireless Communication switch. Some models are equipped with Wireless LAN and Bluetooth functions. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 Wireless LAN standard (Revision B or G) and Turbo Mode.

  • Page 112: Bluetooth Wireless Technology

    TOSHIBA strongly recommend the customer to enable the WEP function. ■ TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. Bluetooth wireless technology Bluetooth™ wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones.

  • Page 113: Wireless Communication Switch

    TOSHIBA 1. Install: ® On Windows2000 or Windows XP, Bluetooth Stack for Windows TOSHIBA does not need signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth Stack. 3. Multi User: On Windows XP, Multi user does not supported.

  • Page 114: Wireless Communication Indicator

    Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.

  • Page 115: Connecting Lan Cable

    Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.

  • Page 116: Cleaning The Computer

    Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

  • Page 117: Using The Hard Disk Drive (Hdd) Protection

    Operating Basics Using the Hard Disk Drive (HDD) Protection There is a function for reducing the risk of damage on HDD in this computer. Using the acceleration sensor built in the computer, HDD Protection detects vibration, shocks and similar signs in the computer, and automatically moves the HDD head to a safe position in order to reduce the risk of damage that could be caused by a head-to-disk contact.

  • Page 118: Toshiba Hdd Protection Properties

    Operating Basics TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start point to All Programs point to TOSHIBA point to Utilities and click HDD Protection setting.

  • Page 119: Detail Properties

    Tablet mode (Battery). Detail Properties To open the Detail Properties window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Figure 4-18 Detail Properties Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.

  • Page 120: Heat Dispersal

    CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on the fan first, then if necessary, lowers the CPU Performance processing speed.

  • Page 121: The Keyboard

    U100 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.

  • Page 122: Function Keys: F1

    Soft keys: FN key combinations The FN (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
  • Page 123 The Keyboard Press FN + F10 or FN + F11 to access the integrated keypad. When activated, the keys with gray markings on the upper surface become numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Refer to the Keypad overlay section in this chapter for more information on how to...

  • Page 124: Hot Keys

    FN, and release and press F2 again to toggle between the settings. Release both FN and F2 to put the new setting into effect. You can also change this setting through the Profile options in TOSHIBA Power Saver.
  • Page 125 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the internal LCD screen turns on.

  • Page 126: Fn Sticky Key

    FN key. FN Sticky key You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.

  • Page 127: Keypad Overlay

    The Keyboard Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the center of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard in figure 5-2.

  • Page 128: Temporarily Using Normal Keyboard (Overlay On)

    The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold FN and press any other key. All keys will operate as if the overlay were off.

  • Page 129: Power And Power-Up Modes

    U100 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.

  • Page 130: Power Indicators

    Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) Battery charge • Operates adaptor is above low • LED: Battery off battery trigger DC IN off connected point Battery charge • Operates is below low •...

  • Page 131: Dc In Indicator

    Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Indicates the AC adaptor is connected and Green supplying proper power to the computer. Indicates a problem with the power supply. Plug Flashing orange the AC adaptor into another power outlet.

  • Page 132: Real Time Clock (Rtc) Battery

    The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.

  • Page 133: Care And Use Of The Battery Pack

    Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
  • Page 134 Do not turn on the PC's power again until an authorized Toshiba service provider has checked it for safety. Continued use could cause a fire or rupture possibly resulting in serious injury or PC failure including but not limited to the loss of data.
  • Page 135 Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Use only battery packs recommended by TOSHIBA as replacements. 3. When installing a battery pack or before moving the PC, always make sure the battery pack is inserted correctly and securely.

  • Page 136: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.

  • Page 137: Monitoring Battery Capacity

    Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.

  • Page 138: Maximizing Battery Operating Time

    ■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: ■...

  • Page 139: Extending Battery Life

    Power and Power-Up Modes Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below.
  • Page 140 Power and Power-Up Modes ■ Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost. ■ In Hibernation mode, data will be lost if you remove the battery pack or disconnect the AC adaptor before the save is completed.

  • Page 141: Toshiba Password Utility

    Figure 6-2 Securing the battery pack 9. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.

  • Page 142: Supervisor Password

    To set a supervisor password, follow the steps below. 1. Click start. 2. Click Run. 3. Enter the following: C:\Program Files\Toshiba\Windows Utilities\SVPWTool\TOSPU.EXE If you set a supervisor password, some functions might be restricted when a user logs on with the user password.

  • Page 143: Power-Up Modes

    Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys FN + F3 to enter Standby mode and FN + F4 to enter Hibernation.
  • Page 144 Power and Power-Up Modes 6-16 User’s Manual...

  • Page 145: Hw Setup

    U100 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.

  • Page 146: Boot Priority

    HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
  • Page 147 HW Setup HDD −> FDD −> CD- The computer looks for bootable files in the ROM −> LAN following order: HDD, floppy disk drive* , CD- ROM* and LAN (Default). HDD −> CD-ROM −> The computer looks for bootable files in the LAN −>...
  • Page 148 HW Setup 3. Use the left/right cursor keys to highlight the boot device you want and press ENTER. ■ If a supervisor password is set only, it is the following. ■ The menu above appears (able to run HW Setup). ■...
  • Page 149 HW Setup Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode. Enables the Wake-up on Keyboard.
  • Page 150 HW Setup Built-in LAN This feature enables or disables the Built-in LAN. Enables Built-in LAN functions (Default). Enabled Disables Built-in LAN functions. Disabled Device Config Device Configuration This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can control Setup by OS (Default).

  • Page 151: Optional Devices

    U100 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC card ■ SD card ■...

  • Page 152: Pc Card

    The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 153: Removing A Pc Card

    Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Slide the PC card eject lever to extend it. 4.

  • Page 154: Formatting An Sd Memory Card

    SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format.

  • Page 155: Sd Card Care

    8. Do not touch the metal part or expose it to liquids or let it get dirty. Creation of a boot disk In TOSHIBA SD Memory Boot Utility, a boot disk can be created with SD memory card. Refer to the Utilities of Chapter 1, Introduction for details.

  • Page 156: Memory Expansion

    When you remove a memory, please do not touch other portions of a computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost.
  • Page 157 Optional Devices 4. Loose a screw securing the memory module cover. The screw is attached to the cover to prevent it from being lost. 5. Slide your fingernail or a thin object under the cover and lift it off. Memory module cover Screw Figure 8-5 Removing the memory module cover 6.

  • Page 158: Removing Memory Module

    Optional Devices 7. Seat the memory module cover and secure it with one screw. Memory module cover Screw Figure 8-7 Seating the memory module cover 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details. 9.

  • Page 159: Battery Pack

    Optional Devices 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.

  • Page 160: Usb Floppy Disk Drive

    Optional Devices USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the Mini-RGB port on the computer.

  • Page 161: I.link (Ieee1394)

    There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.

  • Page 162: Connecting

    Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) connector i.LINK (IEEE1394) port Figure 8-10 Connecting the i.LINK(IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■...

  • Page 163: Libretto Dvd Dock

    Optional Devices libretto DVD Dock The optical media drive can be used by connecting the libretto DVD Dock to this computer. This will allow the computer to view the CD/DVD, write data to the CD-ROM or DVD-ROM, etc. The full-size drive provides high-performance execution of CD/ DVD-ROM- based programs.
  • Page 164 Optional Devices CD/DVD button Pressing this button will launch an application program that allows for watching CD/DVD. Pressing this button in the power-off condition will run Express Media Player. Once Express Media Player is launched, and the front operation panel button is enables. Meanwhile, when Express Media Player is running, pressing this button will do nothing.

  • Page 165: Right Side And Back Side

    Optional Devices Right side and Back side The following figure shows the libretto DVD Dock's right and back side. Undock switch Lock lever Eject switch indicator Figure 8-12 Right and back side the libretto DVD Dock Lock lever Rotating this will lock the libretto DVD Dock connected to the computer so that it cannot be removed.

  • Page 166: Disconnecting The Libretto Dvd Dock

    Optional Devices 4. Gently press the computer downward to connect the computer's docking interface to the libretto DVD Dock's docking interface. Docking holes libretto DVD Dock's front latch Figure 8-13 Connecting the computer to the libretto DVD Dock. 5. Close the lock lever to secure the libretto DVD Dock to the computer. Lock lever Figure 8-14 Closing the lock lever Disconnecting the libretto DVD Dock...
  • Page 167 Optional Devices 4. Open the lock lever. Lock lever Figure 8-15 Opening the lock lever 5. First lift the backside of the computer, remove the computer. User’s Manual 8-17...
  • Page 168 Optional Devices 8-18 User’s Manual...

  • Page 169: Troubleshooting

    U100 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 170: Preliminary Checklist

    Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.

  • Page 171: Hardware And System Checklist

    Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC. Use of incompatible devices may cause injury or may damage your PC.

  • Page 172: Self Test

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...

  • Page 173: Ac Power

    Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down Indicates a problem with the heat dispersal and its DC IN indicator system. Please contact your dealer. is flashing in green AC power If you have trouble turning on the computer with the AC adaptor connected,...
  • Page 174 Fully discharge the battery, then try to charge it again. Check the power consumption settings in TOSHIBA Power Saver utility. Consider using a power saving mode. User’s Manual...

  • Page 175: Password

    Password Problem Procedure Cannot enter Refer to the TOSHIBA Password Utility section in password Chapter 6, Power and Power-Up Modes. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard.

  • Page 176: Internal Lcd Display Panel

    Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, Setup, for more information. Problem Procedure No display Press hotkeys FN + F5 to change the display priority, to make sure it is not set for an external monitor.

  • Page 177: Dvd-Rom&Cd-R/Rw Drive

    Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s disc tray is securely CD/DVD in the drive closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power.

  • Page 178: Dvd Super Multi Drive

    Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.

  • Page 179: Usb Floppy Disk Drive

    Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive.

  • Page 180: Pc Card

    Troubleshooting PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation.

  • Page 181: Fingerprint Sensor

    Troubleshooting Problem Procedure Double-clicking Try changing the double-click speed setting in (AccuPoint control the mouse control utility. buttons) does not work 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Buttons tab. 3.

  • Page 182: Usb

    Troubleshooting Problem Procedure The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility. slow 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Pointer Options tab. 3.

  • Page 183: Memory Expansion

    Troubleshooting Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure Beep sounds. Make sure the memory module installed in the memory slot is compatible with the computer. (Two beeps, a dash and a dot, for a If an incompatible module has been installed, defective memory follow the steps below.

  • Page 184: External Monitor

    Troubleshooting External monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.

  • Page 185: Lan

    Troubleshooting Problem Procedure You can hear a dial If the call is going through a PBX machine, make tone but can’t make a sure the communication application’s tone dial call detection feature is disabled. You can also use the ATX command. Refer to Appendix C, Commands.

  • Page 186: Wireless Lan

    Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on. If problems persist, contact your LAN administrator.

  • Page 187: Disposing Of Pc And Pc Batteries

    All data deletion costs will be borne by you. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.

  • Page 188: Where To Write

    They are your best sources for current information and support. Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia Germany &...
  • Page 189 TOSHIBA Information Systems Systems, Inc. (U.K.) Ltd. 9740 Irvine Boulevard TOSHIBA Court Irvine, California 92618 Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany User’s Manual 9-21...
  • Page 190 Troubleshooting 9-22 User’s Manual...

  • Page 191: Lcd*1

    U100 Chapter 10 Disclaimers This chapter states the Disclaimers information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Disclaimer description is related to TOSHIBA computers. Descriptions related to this computer are marked with a blue *XX in this manual.

  • Page 192: Copy Protection*3

    For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under “Environmental Conditions” in your PC documentation. Contact Toshiba technical service and support, refer to TOSHIBA support section in Chapter 9 Troubleshooting for more information.

  • Page 193: Wireless Lan/Atheros*6

    Disclaimers Wireless LAN/Atheros The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. [54Mbps is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.] The actual transmission speed will be lower than the theoretical maximum speed.

  • Page 194: General Main Memory Disclaimer*12

    Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.

  • Page 195: Appendix A Specifications

    U100 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Refer to User’s Manual about Weight and Size. Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5°C (41°F) to 35°C (95°F) 20% to 80% Non-operating -20°C (-4°F) to 65°C (149°F) 10% to 95% Thermal Gradient 20°C per hour maximum...
  • Page 196 Specifications Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: Full duplex system Fax: Half duplex Communication Data...
  • Page 197 Specifications Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
  • Page 198 Specifications User’s Manual...

  • Page 199: Display Controller And Modes

    U100 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The display controller supports VGA, SVGA and XGA modes at internal LCD display panel.
  • Page 200 Display Controller and Modes Table1 Video modes (VGA) Video Type Resolution Character Colors Scanning mode matrix frequency (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K Text Characters 2, 3 80 × 25 8 × 8 16 of 256K Text Characters...
  • Page 201 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Colors Scanning mode matrix frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K Grph Pels 640 ×...
  • Page 202 Display Controller and Modes Table 2 Video modes Resolution Vertical colors colors frequency (Hz) 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 768 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual) 1600 ×...
  • Page 203 Display Controller and Modes Table 2 Video modes continued Resolution Vertical colors colors frequency (Hz) 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 768 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual) 1600 ×...
  • Page 204 Display Controller and Modes Table 2 Video modes continued Resolution Vertical colors colors frequency (Hz) 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 768 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual) 1600 ×...

  • Page 205: Display Settings

    Display Controller and Modes Display settings 1. You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display or a TV at the same time. *The [Settings] tab is displayed in the following steps;...
  • Page 206 Display Controller and Modes 3) Select the Monitor (CRT display), then select Apply button, because the Primary Device is fixed into Notebook (the display of the computer). Figure B-2 Intel(R) 82852/82855 GM/GME Graphics Controller Prope...(1) 2. Some reproduced DVD picture may not be displayed when the display of the computer and a CRT display are used at the same.
  • Page 207 U100 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
  • Page 208 AT Commands Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default). Selects V.21 when the modem is at 300 bps. Selects Bell 103J when the modem is at 300 bps (default).
  • Page 209 AT Commands Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default). Modem goes off-hook. Result Codes: n=0,1 ERROR Otherwise Request ID information This command displays product information about the modem.
  • Page 210 AT Commands Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
  • Page 211 AT Commands Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
  • Page 212 AT Commands Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
  • Page 213 AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory.
  • Page 214 AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
  • Page 215 AT Commands V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).
  • Page 216 AT Commands Result Codes: n=0,3 ERROR Otherwise C-10 User’s Manual...
  • Page 217 U100 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
  • Page 218 S-registers Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range: 0-225 Default: 0 Units: rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
  • Page 219 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
  • Page 220 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range: 0-255 Default: 2 Units:...
  • Page 221 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...

  • Page 222: At Command Set Result Codes

    S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
  • Page 223 S-registers CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
  • Page 224 S-registers User’s Manual...
  • Page 225 U100 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 226 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
  • Page 227 V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
  • Page 228 V.90 User’s Manual...

  • Page 229: Card Specifications

    U100 Appendix F Wireless LAN Card Specifications Form Factor Mini PCI Type III ■ IEEE 802.11 Standard for Wireless LANS Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.

  • Page 230: Radio Characteristics

    Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
  • Page 231 Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range 2400-2483.5 MHz Channel ID 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457* 2462 2467 2472 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used.
  • Page 232 Wireless LAN Wireless Channels Sets (Turbo Mode) Frequency Range 2400-2483.5 MHz Note Channel ID 2437 US only * *3 Available Area: US (USA, CANADA) only. User’s Manual...

  • Page 233: Ac Power Cord And Connectors

    U100 Appendix G AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following...
  • Page 234 AC Power Cord and Connectors France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.

  • Page 235: Parts Numbers

    U100 Appendix H Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, Memory, External VRAM, HDD, ODD.BAY, Wireless LAN/BT, OS and Warranty. Configurations Memory External VRAM Pentium M 753 (1.2GHz ULV)
  • Page 236 Parts Numbers User’s Manual...
  • Page 237 U100 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange...
  • Page 238 VRT: voltage reduction technology WXGA: wide extended graphics array XGA: extended graphics array AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
  • Page 239 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
  • Page 240 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
  • Page 241 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
  • Page 242 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 243 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
  • Page 244 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 245 Glossary jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
  • Page 246 Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
  • Page 247 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
  • Page 248 Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device.
  • Page 249 Glossary terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. TTL: Transistor-transistor logic.
  • Page 250 Glossary Glossary-14 User’s Manual...
  • Page 251 AC adaptor 1-5 controller 1-7 additional 1-16 hinge 2-8 connecting 3-6 opening 3-8 DC IN 15V jack 2-2 DLA for TOSHIBA 1-15 4-22 ASCII characters 5-8 Docking port 1-8 Documentation list 1-3 Battery DVD Super Multi drive 1-6 charging 6-8...
  • Page 252 Index FN + CTRL (enhanced key- Internal LCD screen bright- board simulation) 5-3 ness increase 5-5 FN + ENTER (enhanced key- power save mode 5-4 board’s numeric keypad) 5-3 sound mute 5-4 FN + ESC (sound mute) 5-4 standby 5-4 FN + F1 (instant security) 5-4 wireless setting 5-5 FN + F10 (Arrow mode) 5-3...
  • Page 253 Index turning on the overlays 5-7 problems 9-12 removing 8-3 Pointing Device 1-7 LAN 1-9 4-36 AccuPoint 2-8 cable types 4-36 AccuPoint control buttons 2- connecting 4-37 disconnecting 4-37 problems 9-12 jack 2-5 Ports problems 9-17 Docking port 1-8 libretto DVD Dock 1-16 8-13 i.LINK 1-8 Mini-RGB 1-7...
  • Page 254 TOSHIBA Assist 1-14 PC card 9-12 TOSHIBA ConfigFree 1-15 Pointing Device 9-12 TOSHIBA Controls 1-13 Power 9-4 TOSHIBA PC Diagnostic Tool 1- SD card 9-11 Self test 9-4 TOSHIBA Power Saver 1-13 Sound System 9-15 TOSHIBA SD Memory Boot Util-...

Table of Contents