Page 1 Portégé 3500 3500 Portable Personal Computer User’s Manual User's Manual...
Page 2 Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. is a Certification Mark of the Wireless Ethernet Compatibility Alliance, Inc.
Page 3 Portégé 3500 The equipment has been approved to [Commission Decision "CTR21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 4 Portégé 3500 TOSHIBA computers are designed to optimise safety, minimise strain and withstand the rigours of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 5 This product was designed to fulfil the EMC (electromagnetic compatibility) requirements to be observed for so-called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments".
Page 6 Malfunction of, or data loss from, this product caused by disturbances generated by other devices or machines in the near surrounding area Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non-approved working environments before use.
Page 7 RC4 encryption algorithm as defined in the IEEE 802.11 standard on wireless LANs. The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any Wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ■...
Page 8 Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 9 Portégé 3500 Do not use the Wireless Products for controlling equipment: ■ Equipment directly linked with human life corresponds to the following. ■ Medical equipment such as life support systems, equipment used in operations, etc. ■ Exhaust systems for gases such as poisonous gas etc. and exhaust systems for smoke.
Page 10 Depending on environment, radio waves can not reach to the product. The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.
Page 11 Portégé 3500 This device complies with the essential requirements of the R&TTE Directive 1999/5/EC with essential test suites as per standards: ■ EN 60950 Safety of Information Technology equipment ■ ETS 300 328 Technical requirements for radio equipment ■ ETS 300 826 General EMC requirements for radio equipment. België/Belgique: For outdoor usage only channel 10 (2,457 MHz) and 11 (2,462 MHz) is allowed.
Page 12 This device must accept any interference that may cause undesired operation. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
Page 13 Portégé 3500 The Toshiba Wireless LAN Mini PCI Card will be installed with one of three types of antennas. One of these antennas, when installed will be located under the keyboard. The other two antenna types, when installed are located at the upper edge of the LCD screen.
Page 14 Portégé 3500 In Japan, the frequency bandwidth of 2,400•2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on devices incorporating this product. 2.
Page 15 Portégé 3500 This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.
Page 16: Table Of Contents
Table of Contents 4SVXÃKÃ 8EFPI SJ 'SRXIRXW General Precautions ..............xiii Preface ..................xxi Manual contents ................xxii Conventions................xxiii Chapter 1 Introduction............... 1-1 Equipment checklist ..............1-1 Features ..................1-3 Special features ................1-8 Utilities ..................1-10 Options ..................1-12 Chapter 2 The Grand Tour ............2-1 Front with the display closed ............2-1 Left side ..................2-3 Right side..................2-5...
Page 17 Table of Contents Chapter 4 Operating Basics ............4-1 Using the Touch pad ..............4-1 Using the TOSHIBA tablet pen............ 4-3 Changing to the Tablet mode ............4-9 Changing to the laptop mode............ 4-12 Using the optional USB FDD Kit..........4-12 Wireless communications............
Page 18 Problem solving process..............9-1 Hardware and system checklist ...........9-3 Appendix A Specifications Appendix B AC Power Cord and Connectors Appendix C The TOSHIBA International Warranty Appendix D Keyboard Layouts Appendix E Display Controller and Modes Appendix F If your computer is stolen...
Page 19: Preface
Preface Congratulations on your purchase of the TOSHIBA Portégé 3500 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Portégé 3500 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 20 Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad (TOSHIBA tablet pen), optional external diskette drive, wireless communication features, LAN and internal modem. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys.
Page 21 Preface This manual uses the following formats to describe, identify, and highlight terms and operating procedures. On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary. Icons identify ports, dials, and other parts of your computer.
Page 22 Preface Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 23 Preface Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.
Page 24: Equipment Checklist
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Carefully unpack your computer. Save the box and packing materials for future use.
Page 25 Introduction ■ The following software is preinstalled: ■ ® Microsoft Windows XP Tablet PC Edition ■ Modem driver ■ Display driver ■ Touch Pad driver ■ Sound driver ■ Bluetooth driver ■ Wireless LAN Driver ■ Software Modem Driver ■ SD card Driver ■...
Page 26: Features
Introduction The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: III processor 1.33 GHz - ®...
Page 27 Introduction The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 12.1" XGA-TFT, 1024 horizontal x 768 vertical pixels, up to 16 M colours Graphics controller A 128-bit graphics controller maximizes display performance.
Page 28 Introduction Headphone Enables connection of a stereo headphone Microphone Enables connection of a monaural microphone Infrared This infrared port is compatible with Infrared Data Association (IrDA 1.1) Fast InfraRed (FIR) standards. It enables cableless 4 Mbps data transfer with IrDA 1.1 compatible external devices.
Page 29 Introduction Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to Appendix H. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line.
Page 30 Windows XP Tablet PC Edition is preinstalled on the hard disk. Refer to the preinstalled software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use.
Page 31 Introduction The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
Page 32 Introduction Panel power on/off This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. You can specify the setting in the When I close the lid item of the System Power Mode window in Power Saver.
Page 33: Utilities
This software enables the user to run an application or to show home page by drawing a simple mark on the display with the TOSHIBA tablet pen. You can customize the action to boot the computer and to run the application.
Page 34 Introduction TOSHIBA Console TOSHIBA Console is a graphical user interface that provides easy access to help and services. It is the default function launched by the TOSHIBA Console button. Bluetooth TOSHIBA This software enables communication between stack remote Bluetooth devices. Refer to the Quick Start Guide.
Page 35: Options
Bluetooth. It is installed by dealers only. TOSHIBA tablet pen TOSHIBA tablet pen can be purchased from your TOSHIBA dealer. Use it as a spare to your computer. Spare pen tip and draw-out tool are included. DVD-ROM Drive DVD-ROM Drive (PA3246) is available as an optional external optical disk drive.
Page 36: Chapter 2 The Grand Tour
The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. The figure below shows the computer’s front with its display panel in the closed position. ISPLAY ATTERY LATCH BUTTON OWER SOURCE OLUME CONTROL...
Page 37 The Grand Tour Microphone jack A standard 3.5 mm (in dia.) mini microphone jack enables connection of a monaural microphone or other device for audio input. Headphone jack A standard 3.5 mm mini headphone jack enables connection of a stereo headphones (16 ohm minimum) or other device for audio output.
Page 38: Left Side
The Grand Tour The figure below shows the computer’s left side. IRELESS CARD CARD SLOT INDICATOR COMMUNICATION SWITCH OMPACT FLASH ODEM CARD SLOT MODULE SLOT WITH COVER OPENED The left side of the computer User’s Manual...
Page 39: Right Side
The Grand Tour Compact Flash This slot accommodates Compact Flash module module slot of various capacities. You cannot use Compact Flash module that does not conform to CFA specifications. You can also use Compact Flash I/O module other than memory module. Keep foreign objects out of the Compact Flash module slot.
Page 40: Back Side
The Grand Tour The figure below shows the computer’s right side. ECURITY LOCK SLOT The right side of the computer Security lock slot A security cable is attached to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft The figure below shows the computer’s back side.
Page 41 The Grand Tour Fan vent Provides air flow for the fan. Be careful not to block the fan vent. Also be careful to keep foreign objects out of the vent. A pin or similar object can damage the computer’s circuitry. DC IN 15V The AC adaptor is connected to this socket.
Page 42: Underside
AC adaptor is not connected. The Batteries section in Chapter 6, Power and Power-Up Modes, describes how to access the Battery Pack. Battery Packs can be purchased from your TOSHIBA dealer to extend the computer’s battery operating time. User’s Manual...
Page 43: Front With The Display Open
The Grand Tour ISPLAY LATCH ISPLAY SCREEN OSHIBA TABLET PEN ISPLAY HINGE RROW BUTTON NTER ENU BUTTON FROM LEFT TO RIGHT PEAKER OUCH OUCH PAD OWER ENSOR BUTTON SWITCH CONTROL BUTTONS ICROPHONE OWER BUTTON LOCK INDOWS SECURITY TABLET BUTTON The front with the display open Portégé...
Page 44 TOSHIBA tablet pen Pen is contained on the left hand side of display. A pen enables data entry directly through display screen. Refer to the Using the TOSHIBA tablet pen section Chapter 4, Operating Basic. Microphone A built-in microphone can be used to record monaural sounds into your application.
Page 45 The Grand Tour Enter/Menu button This button functions as the same to Enter key when tapped, or shows the menu screen when pressed for more than a second. Arrow button (2) This button functions as the same to ↓ key. Speaker The speaker emits sound generated by your software as well as audio alarms, such as low...
Page 46: Indicators
The Grand Tour The figure below shows the indicators, which light when various computer operations are in progress. IRELESS COMMUNICATION DC IN OWER ATTERY The power source/system indicators 4S[IV WSYVGIW]WXIQ MRHMGEXSVW DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor.
Page 47 The Grand Tour The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows, the keypad overlay lets you control the cursor. When the F11 key indicator glows, the keypad overlay lets you enter numbers.
Page 48: Ac Adaptor
The AC adaptor Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. User’s Manual 2-13...
Page 49: Chapter 3 Getting Started
Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Page 50 Getting Started Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
Page 51 Getting Started In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Page 52 Getting Started The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to the figure below. ELOW EYE LEVEL DEGREE ANGLES OOT REST...
Page 53 Getting Started A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.
Page 54 Getting Started TOSHIBA 3500 computer can be used in two ways; ordinary laptop PC and tablet PC. You can use the computer as tablet PC that is operated with attached TOSHIBA tablet pen by turning LCD panel in 180 degrees and closing it.
Page 55 Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. 1. Connect the power cord to the AC adaptor.
Page 56 Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN port on the left side of the computer. Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator on the front of the computer should glow.
Page 57 Getting Started This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time in this chapter.
Page 58 Getting Started When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Tablet PC edition Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully.
Page 59 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.
Page 60 1. Open the Windows Control Panel. 2. Open Performance and Maintenance. 3. Open TOSHIBA Power Saver. 4. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button. 5. Select the Power Save Modes window.
Page 61 Standby, it might not be restored when the computer wakes up from standby. To prevent the computer from automatically entering standby mode, disable Standby in TOSHIBA Power Saver. Open the Standby setting. That action, however, will nullify the computer’s Energy Star compliance. User’s Manual...
Page 62 1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. To enable it, select the TOSHIBA Power Saver icon in the Control Panel and open the System Power Mode item.
Page 63 Getting Started Standby will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise. User’s Manual 3-15...
Page 64 If preinstalled files are damaged, use the Product Recovery disk or TOSHIBA Tools & Utilities CD-ROM to restore them. To restore the operating system and all preinstalled software, follow the steps below. To restore the operating system and all preinstalled software, follow one of the instruction list below.
Page 65 1. Load the Product Recovery disk in the drive and turn off the computer’s power. 2. Hold down the C key and turn on the power. When the TOSHIBA logo appears, release the C key. 3. Follow the on-screen instructions.
Page 66: Using The Touch Pad
Operating Basics This chapter gives information on basic operations including using the Touch pad, the TOSHIBA tablet pen, the optional external diskette drive, the wireless communication, LAN and the internal modem. It also provides tips on caring for your computer and on heat dispersal.
Page 67 Operating Basics For some functions, you can tap the Touch pad instead of pressing a control button. Click Tap the Touch pad once. Double-click Tap the Touch pad twice. 1. Select the material you want to move. Drag and drop 2.
Page 68 IDE SWITCH ERASER EN POINT The TOSHIBA tablet pen You can use the tablet pen to execute actions and enter data. Hold the tablet pen in a natural position and tap, press or trace on the screen lightly. Before you begin using the Portégé 3500 for the first time, you will need to calibrate the tablet pen.
Page 69 11. Do not use a broken pen tip. TOSHIBA is not liable to the quality problem of the products due to the use of the tablet pen in an environment where above conditions are not satisfied because of the use by unspecified number of users...
Page 70 Operating Basics Installing the tablet pen The tablet pen is included in the product when purchased. Take out the tablet pen from the carton and install it to the computer as the following. 1. Insert the head of the tablet pen into the groove first. 2.
Page 71 Operating Basics Removing the tablet pen 1. To remove the tablet pen from the groove, press the tablet pen at the head. 2. Tail of the tablet pen rises up. Drawing out the tablet pen You can use the tablet pen to enter data, start programs, move objects and execute other actions.
Page 72 Operating Basics Lightly tap the tip of pen twice on an object and lift it immediately to execute an action. A double-tap is similar to double-clicking the left Touch pad control button. Touch the tip of pen to the display screen and hold it there to display a pop-up menu or other action.
Page 73 Short and worn pen point is difficult to pull out. Replace the pen point with refill before it becomes too short. TOSHIBA recommends the customer to keep another pen set as a spare. You can buy the pen set from TOSHIBA dealer.
Page 74: Changing To The Tablet Mode
Operating Basics To change the laptop mode to the tablet mode, follow the instructions below. Changing to the Tablet mode (1) Place the computer on a stable, flat place such as a desktop and rotate the display panel slowly, holding the panel at its lower part. The display panel is designed not to rotate more than 180 degrees.
Page 75 Operating Basics 1. Open the display panel to the upright position. Changing to the Tablet mode (2) 2. Rotate the display panel clockwise slowly. Do not apply excessive rotating force to the display panel. It causes damage of the display panel. 3.
Page 76 Turn the Display latch downward. Insert the Display latch in the slit. Press the display panel downward softly. You can set the orientation of the desktop screen just after rotating the -> -> display from Start All Programs TOSHIBA Rotation Utility. User’s Manual 4-11...
Page 77 Operating Basics To change the Tablet mode to the laptop mode, follow the instructions below. 1. Press the Display latch and raise the display to the upright position carefully. 2. Rotate the display counter-clockwise slowly. 3. Turn the display latch toward you for the next closing of the display. An optional 3 ½"...
Page 78 Operating Basics The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 while it is operating. Do not set anything on top of the diskette drive. If you need to boot the computer from the diskette drive or if you use an OS that does not support USB, you must set the USB-FDD Legacy Emulation feature in HW Setup to Enabled.
Page 79 Operating Basics When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive.
Page 80: Wireless Communications
Be sure to enable WEP (encryption) function. Otherwise your computer will allow the illegal access by outsider through wireless LAN to cause illegal intrusion, eavesdropping, and loss or destruction of stored data. TOSHIBA strongly recom-mend the customer to enable the WEP function. User’s Manual 4-15...
Page 81 Operating Basics Bluetooth wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. You cannot use the built-in Bluetooth functions and an optional Bluetooth PC card simultaneously. Bluetooth wireless technology has the following features: The Bluetooth radio transmitter and receiver operates in the 2.45 GHz band, which is license-free and compatible with radio systems in most countries in the world.
Page 82 W-LAN. Open or click the following: start, Control Panel, System, Hardware Device Manager, Network adapters, TOSHIBA Wireless LAN Mini PCI Card and Enable. Indication of Wireless Communication Standards (Wireless LAN and Bluetooth).
Page 83 Operating Basics The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled.
Page 84 Operating Basics Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN Active indicator glow in yellow.
Page 85 Operating Basics Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speaker, "howling" may be heard under certain conditions.
Page 86: Modem
1. Click Start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 87 Operating Basics Click the icon with the secondary mouse button to display the following menu. The menu list (Windows XP Tablet PC Edition You can enable or disable the following settings: Region Select Utility starts automatically when you start up the operating system.
Page 88 Operating Basics Select this item to display the dialing properties. If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select Japan region mode. It is illegal to use the modem in Japan with any other selection.
Page 89 Operating Basics To connect the internal modem cable, follow the steps below: 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack. Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.
Page 90: Moving The Computer
Operating Basics To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 91 CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Power Save Mode window in TOSHIBA Power Saver. Maximum Turn on the fan first, then if necessary, lower the performance CPU processing speed.
Page 92: Typewriter Keys
The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 93: Soft Keys: Fn Key Combinations
The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 94: Hot Keys
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the side face become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys.
Page 95 The Keyboard Power save mode: Pressing Fn + F2 changes the power save mode. If you press Fn + F2, the Power Save Mode is displayed in a dialog box. Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the Plugged in or Running on batteries item of the Power Saver Properties window in Power Saver.
Page 96 When you press those hotkeys, the current setting will change and be displayed as an icon. You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an F number key.
Page 97: Keypad Overlay
The Keyboard The keyboard provides two keys that have special functions in Windows : one activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary mouse button. Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
Page 98 The Keyboard 2YQIVMG QSHI To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the figure below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay While using the overlay, you can temporarily access the normal keyboard without turning off the overlay:...
Page 99 The Keyboard While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry.
Page 100: Power Conditions
Â Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery.
Page 101: Power Indicators
Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â Table: Power conditions continued Power on Power off (no operation) AC adaptor Battery charge is Operates above low battery — LED: Battery off connected trigger point DC IN off Battery charge is Operates below low battery — LED: Battery flashes in trigger point orange DC IN off...
Page 102 Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, contact TOSHIBA dealer. Refer to Chapter 9, Trouble shooting TOSHIBA support. No light Under any other conditions, the indicator does not light.
Page 103 Dispose of the battery as required by local ordinances or regulations. Use only battery recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAMs, so if the computer loses power it will be lost.
Page 104 Check system. Then press [F1] key ..The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
Page 105 Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â The Battery Pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your Battery Pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
Page 106 Â Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â Mishandling of batteries can cause death, serious injury or property damage. Carefully observe the following advisories Danger: Indicates an imminently hazardous situation, which could result in death or serious injury, if you do not follow instructions Warning: Indicates a potentially hazardous situation, which could result it death or serious injury, if you do not follow instructions.
Page 107 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.
Page 108 Â Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely, Standby and Suspend will not function and data in memory will be lost. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries 7.
Page 109: Battery Types
The Battery indicator glows in orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the Battery Pack. Do not attempt to charge the Battery Pack with any other charger.
Page 110 In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery Maximizing battery operating time.
Page 111 Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer, for example, whether you enable battery-power saving options. The computer provides a battery save mode to conserve battery power.
Page 112 Â Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â To maximize the life of your Battery Pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the Battery Pack fully discharges. Before doing so, follow the steps below. 1.
Page 113: Replacing The Battery Pack
6. Confirm that the Battery lock indicator shows red. 7. Push the battery release lever to the left to free the battery pack for removal. For environmental reasons, do not throw away a spent Battery Pack. Please return spent Battery Packs to your TOSHIBA dealer. 6-14 Portégé 3500...
Page 114 Â Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â ATTERY LOCK ATTERY LOCK ATTERY RELEASE LEVER INDICATOR Removing the Battery Pack (1) Removing the Battery Pack (2) User’s Manual 6-15...
Page 115 Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. 2. Insert the Battery Pack.
Page 116 Â Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â If you registered a password as user, you must enter it to start the computer. For more information about how to set a password, refer to Chapter 7, HW Setup and Passwords. To start up the computer with the password, follow these steps: 1.
Page 117: Power-Up Modes
Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. You can specify the setting in TOSHIBA Power Saver. You can use hotkeys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.
Page 118: Tablet Mode
Â Rƒ‘s†Âi‚rÂRƒ‘s†W„ÂIƒrs‡Â You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. However, when the system is running in the tablet mode, it does not shut down even if the display panel is closed.
Page 119 TOSHIBA HW Setup lets you configure settings for display, CPU, boot priority, USB, LAN, general, password and device config. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
Page 120 HW Setup and Passwords The HW Setup window contains the following tabs: display, CPU, boot priority, USB, LAN, general, password, device config. This window displays the BIOS version and contains two buttons: Default and About. Return all HW Setup values to the factory Default settings.
Page 121 HW Setup and Passwords Registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks.
Page 122 HW Setup and Passwords This option lets you set the device configuration. BIOS sets all devices. All Devices Operating system sets devices that it can Setup by OS control. (Default) This tab lets you customise your computer’s display settings for either the internal LCD screen or for an external monitor.
Page 123 HW Setup and Passwords This option sets the priority for booting the computer. Select from the following settings: HDD ! FDD The computer looks for bootable files in the ! CD-ROM ! LAN following order: HDD, diskette drive, CD-ROM* and LAN. (Default) FDD ! HDD The computer looks for bootable files in the ! CD-ROM ! LAN...
Page 124 [RPL] PC card HDD boot is supported only by the PC card slot on the computer. Support is guaranteed only for TOSHIBA PC card HDDs. When you assign a PC card HDD top priority, "PC" is not displayed. However, the PC card HDD takes the position of HDD in the Boot Priority Options list above.
Page 125 HW Setup and Passwords When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Standby mode. Enables the Wake-up on Keyboard.
Page 126 Disables built-in LAN functions. Disabled Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file. Portégé 3500...
Page 127: Chapter 8 Optional Devices
PC cards ■ SD cards ■ Compact Flash ■ Memory module ■ Battery Pack ■ Universal AC Adaptor ■ Battery Charger ■ USB FDD Kit ■ External monitor ■ Security lock ■ TOSHIBA tablet pen set. W‡s†k‡ÂIi‚‰i€Â (!Â User’s Manual...
Page 128 The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 129 Optional Devices To remove the PC card, follow the steps below: 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5.
Page 130 Optional Devices To install an SD card, follow the steps below. 1. Insert the SD card. 2. Press gently to ensure a firm connection. CARD Inserting an SD card Make sure the SD card is oriented properly before you insert it. To remove an SD card, follow the steps below.
Page 131 Optional Devices Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card.
Page 132 Optional Devices This slot accommodates Compact Flash with various memory capacities. You cannot use Compact Flash that does not conform to CFA specifications. You can also use Compact Flash I/O module other than memory module. To install a Compact Flash module, follow the steps below. 1.
Page 133 Optional Devices To remove a Compact Flash, follow the steps below. 1. Right click (right button of the Touch Pad) on the Compact Flash drive’s icon and select eject from the pop-up menu. 2. Press the Compact Flash eject button to extend it. 3.
Page 134 • It is strongly recommended to leave the replacing of memory module preinstalled in Slot A to TOSHIBA dealer because the installing or replacing of memory module in Slot A needs skill. Place a mat beneath the computer to prevent making a scratch on the lid when replacing the memory module.
Page 135 Optional Devices If you install a memory module that is not compatible with the computer, beep will sound when you turn on the power. If the module is installed in slot A, there will be a long beep (1 second) followed by two short beeps (0.5 second each).
Page 136 Optional Devices 6. Remove two screws (right and left at the both right and left end of the keyboard) fixing the keyboard. Removing the keyboard (1) Be careful not to drop the screw inside the computer when removing. 7. Press the keyboard to the other side. Turn the keyboard upside down when a flat cable appears.
Page 137 Optional Devices Removing the keyboard (3) 8. Raise the insulation sheet covering the memory module to appear the module. NSULATION HEET Raising the insulation sheet User’s Manual 8-11...
Page 138 Optional Devices 9. Push the latches to the outside to release the module. A spring will force one end of the module up. Removing the memory module 10. Pinch the module by the sides and pull it out. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.
Page 139 Optional Devices Installing memory module in Slot A (2) 12. Seat the insulation sheet to cover the module. Be sure to check that the insulation sheet is returned to the original position to cover the memory module. 13. Insert two tabs into slit of the computer case and seat the keyboard at the original position.
Page 140 Optional Devices Removing the memory module cover Be careful not to drop the screw inside the computer when removing. 6. Lift one side of the insulator sheet and fit the module’s connectors into the computer’s connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection.
Page 141 Optional Devices Inserting a module (2) Inserting a module (3) 8. Seat the cover and secure it with one screw. 9. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes. 10. Turn the power on and make sure the added memory is recognized. When you view the memory display, the total amount will be reduced by 16 MB, which is used for VRAM.
Page 142 Optional Devices To remove the memory module, make sure the computer is in boot mode then: 1. Be sure the power is off and all cables are disconnected from the computer. 2. Turn the computer upside down and remove the battery and one screw securing the memory module cover.
Page 143 Optional Devices You can increase the portability of the computer with Battery Packs (PA3228U). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes. If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor (PA3241 or PA3083) for each location will reduce the weight and bulk of your carrying load.
Page 144: Security Lock
Optional Devices A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
Page 145: Chapter 9 Troubleshooting
Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 146 Troubleshooting Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.
Page 147 Troubleshooting The problems may be caused by your software or diskette. If you cannot load a software package, the media (usually a diskette) may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation.
Page 148 When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the HW Setup program.
Page 149: Heat Dispersal
Troubleshooting If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Resume mode and shut down. Problem Procedure Computer shuts down Leave the computer off until the DC IN indicator and DC IN indicator stops blinking. blinks orange If the computer has reached room temperature and still does not start, or if it starts but shuts...
Page 150 Troubleshooting If you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t power The battery may be discharged. Connect the the computer AC adaptor to charge the battery.
Page 151 Troubleshooting Problem Procedure Cannot enter password Refer to the Password section in Chapter 7, HW Setup and Passwords. Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys Check that the numeric keypad overlay is not selected.
Page 152 Troubleshooting Problem Procedure Computer does not Check if a diskette is in the diskette drive. If a boot from hard drive diskette is inserted, remove it and reboot. There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented.
Page 153 Troubleshooting Refer also to the documentation for your IrDA compatible device and related software. Problem Procedure Infrared devices do not Check that the device is connected to an electric work as expected outlet. Make sure the outlet is supplying power by plugging in an appliance.
Page 154 Troubleshooting Unable input from Adjust the setting in the following procedure. tablet pen 1. Open the Control Panel and click Printer and other Hardware. 2. Click the Tablet and Pen setting. 3. Adjust setting of each item of Pen options tab and click OK.
Page 155 Troubleshooting Problem Procedure On-screen pointer does The system might be busy. If the pointer is does not respond to mouse not respond to shaped as an hourglass, wait for operation it to resume its normal shape and try again to move it.
Page 156 Troubleshooting Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write in Make sure the card is not write protected. an SD card You cannot read a file Make sure the target file is on the SD Card...
Page 157 Troubleshooting Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not Make sure that the external monitor’s power turn on switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet.
Page 158 Troubleshooting Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.
Page 159 Troubleshooting Refer to the online help files for Appendix C and D. Problem Procedure Communication Make sure the computer’s internal modem software can’t settings are correct. Refer to Modem Properties initialise modem in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can't make a sure the communication application’s tone dial...
Page 160 Troubleshooting Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. If problems persist, consult your LAN administrator. Wake-up on LAN Make sure the AC adaptor is connected. The does not work Wake-up on LAN function consumes power even when the system is off.
Page 161: Appendix A Specifications
Specifications 4SVXÃKÃ %TTIRHM\ % 7TIGMJMGEXMSRW This appendix summarises the computer’s technical specifications. Size With TFT display 295 (w) x 234 (d) x 31(front)/33 (rear), 36 (max) millimeters (does not include the thicker part of the bottom of the computer) Weight Hard disk Memory...
Page 162 Specifications AC adaptor 100 - 240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 3.0 amperes Network control unit (NCU) Type of NCU Telephone line (analogue only) Type of line Pulse Type of dialling Tone AT commands Control command EIA-578 commands Computer’s speaker...
Page 163 Specifications 'SQQYRMGEXMSR WTIGMJMGEXMSRW Data: Full duplex Communication system Fax: Half duplex Data Communication ITU-T-Rec protocol V.21/V.22/V.22bis/V.32 (Former CCITT) /V.32bis/V.34/V.90 Bell 103/212A ITU-T-Rec V.17/V.29/V.27ter/ (Former CCITT) V.21 ch2 Communication Data transmission and reception speed 300/1200/2400/4800/7200/9600/12000/ 14400/16800/19200/21600/24000/26400/ 28800/31200/ 33600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/ 36000/37333/38666/40000/41333/42666/ 44000/45333/46666/48000/49333/50666/...
Page 164 AC Power Cord and Connectors 4SVXÃKÃ & %TTIRHM\ & %' 4S[IV 'SVH ERH 'SRRIGXSVW The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country in which it is used. All cords must meet the following specifications: Length: Minimum 2 metres...
Page 165 AC Power Cord and Connectors Italy: The Netherlands: KEMA Norway: NEMKO Sweden: SEMKO Switzerland: United Kingdom: Japan: DENANHO In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S.
Page 166 AC Power Cord and Connectors The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada United Kingdom UL approved CSA approved Australia Europe AS approved Approved by the appropriate agency User’s Manual...
Page 167 TOSHIBA representation for registration. On the following pages is a list of the TOSHIBA companies who can be contacted if a claim on the warranty needs to be made. If users need further addresses in eastern Europe or outside Europe, these are available from the national or European companies.
Page 168 P.O. Box 1224, Cairo 11511 Estonia ServiceNet EE Tel: +372-6504-949 Parnu mnt. 142A Fax: +372-6504-916 11317 Tallinn http://www.gnt.ee Finland Scribona Suomi OY / TOSHIBA Digital Media Tel: +358-9-5272555 Sinimäentie 8 A Fax: +358-9-5272500 P .O.Box 83 http://www.toshiba.se 02630 ESPOO France TOSHIBA Systèmes (France) S.A.
Page 169 Netherlands TOSHIBA Information Systems Benelux B.V. Tel: +31-0900-1000-1000 Rivium Boulevard 41 Fax: +31-10-2882-390 2909 LK Capelle a/d IJssel http://www.toshiba.nl Norway Scribona Norge A/S; TOSHIBA PC Service Tel: +47-22-897-189 Stålfjæra 20 Fax: +47-22-897-166 P.O.Box 51, Kalbakken http://www.toshiba.se 0901 OSLO User’s Manual...
Page 170 Unit 6A, Fax: +27-11-314-2424 Mifa Industrial Park, http://www.cs.co.za/it.htm 399 George Street, 1685 Midrand Spain TOSHIBA Information Systems (España) S.A. Tel: +34-91-6606-700 Parque Empresarial San Fernando Fax: +34-91-6606-760 Edificio Europa, 1a Planta, Escalera A http://www.toshiba.es 28831 (Madrid) San Fernando de Henares...
Page 171 TOSHIBA Information Systems (UK) Ltd. Tel: +44-1932-828828 Kingdom TOSHIBA Court, Weybridge Business Park Fax: +44-1932-822958 Addlestone Road http://www.toshiba.co.uk Weybridge KT15 2UL United States TOSHIBA America Information Systems, Inc. Tel: +1-949-583-3000 9740 Irvine Blvd. Fax: +1-949-583-3345 Irvine, CA 92713-9724 http://www.toshiba.com Yugoslavia CT Computers...
Page 172 Keyboard Layouts Belgian W‡s†k‡ÂIi‚‰i€Â @!Â User’s Manual...
Page 173 Keyboard Layouts Danish French Portégé 3500...
Page 174 Keyboard Layouts German Italian User’s Manual...
Page 175 Keyboard Layouts Norwegian Spanish Portégé 3500...
Page 176 Keyboard Layouts Swedish Swiss-German User’s Manual...
Page 177 Keyboard Layouts UK English US English Portégé 3500...
Page 178 Display Controller and Modes The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors.
Page 179 Display Controller and Modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
Page 180 Display Controller and Modes Table Video modes (Landscape) Video Type Resolution Character LCD colours Scanning mode matrix (pels) colours frequency vertical 0, 1 40 x 25 8 x 8 16 of 256k 16 of 256k 70Hz Text Characters 2, 3 80 x 25 8 x 8 16 of 256k...
Page 181 Display Controller and Modes Table Video modes (Landscape) Video Type Resolution Character LCD colours Scanning mode matrix (pels) colours frequency vertical SVGA 640 x 480 – 256 of 256k 256 of 256k 60/75/85Hz Grph Pels SVGA 800 x 600 – 256 of 256k 256 of 256k 60/75/85Hz Grph...
Page 182 Display Controller and Modes Table Video modes (Landscape) Video Type Resolution Character LCD colours Scanning mode matrix (pels) colours frequency vertical SVGA 480 x 640 256 of 256K 256 of 256K 60/75/85Hz Grph Pels SVGA 600 x 800 256 of 256K 256 of 256K 60/75/85Hz Grph Pels...
Page 183 What is your address, phone, and fax number? To register the theft, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) on the next page. ■ Attach a copy of your receipt showing where your computer was purchased.
Page 184 If your computer is stolen 837,-&% 8LIJX 6IKMWXVEXMSR Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 925 Country stolen: Machine type: (e.g. Portégé 3500) Model number: (e.g. PXXXXX YXT) Serial number: (e.g.
Page 185 ASCII Character Codes 4SVXÃKÃ %TTIRHM\ + %7'-- 'LEVEGXIV 'SHIW This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, The Keyboard).
Page 186 ASCII Character Codes Portégé 3500...
Page 187 ASCII Character Codes User’s Manual...
Page 188 ASCII Character Codes Portégé 3500...
Page 189 ASCII Character Codes User’s Manual...
Page 190 ASCII Character Codes Portégé 3500...
Page 191 AT Commands 4SVXÃKÃ %TTIRHM\ , %8 'SQQERHW In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 192 AT Commands This command repeats the last command string entered. Do not precede this command with an AT prefix or conclude it by pressing Enter. This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps.
Page 193 AT Commands This command instructs the modem to dial a telephone number. Enter n (the telephone number and any modifiers) after the ATD command. Any digit or symbol (0-9, *, #, A, B, C, D) may be dialed as touch-tone digits. Characters such as spaces, hyphens, and parentheses do not count.
Page 194 AT Commands This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the modem is in command mode. Disables echo to the computer. Enables echo to the computer (default). Result Codes: n = 0, 1 Otherwise ERROR...
Page 195 AT Commands This command displays product information about the modem. Returns modem identity string and driver version number. Same as I0. Returns region ID in English. Result Codes: n = 0, 3, 9 Otherwise ERROR This command sets speaker volume to low, medium, or high. Low volume.
Page 196 AT Commands This command turns the speaker on or off. The speaker is off. The speaker is on until the modem detects the carrier signal (default). The speaker is always on when modem is off-hook. Speaker is on until the carrier is detected, except when dialing.
Page 197 AT Commands Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). This command issues a retrain before returning to on-line data mode. This command issues a rate renegotiation before returning to on-line data mode. Result Codes: n = 0, 1, 3 Otherwise...
Page 198 AT Commands Result codes are informational messages sent from the modem and displayed on your monitor. Basic result codes are OK, CONNECT, RING, NO CARRIER, and ERROR. The ATQ command allows the user to turn result codes on or off. Enables modem to send result codes to the computer (default).
Page 199 AT Commands This command selects which result codes will be used by the modem. Command Dial Busy Supported Result Code tone signal detect detect Disable Disable OK, CONNECT, RING, NO CARRIER, ERROR Disable Disable OK, RING, NO CARRIER, ERROR, CONNECT <RATE> Enable Disable OK, RING, NO CARRIER, ERROR,...
Page 200 AT Commands Disabled: The modem ignores any busy tones it receives. Enabled: The modem monitors for busy tones. Result Codes: n = 0, 1, 2, 3, 4, 5 Otherwise ERROR The modem performs a soft reset and restores (recalls) the configuration profile according to the parameter supplied.
Page 201 AT Commands This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0 Ignore. The modem ignores the true status of DTR and treats it as always on. This should only be used if your communication software does not provide DTR to the modem.
Page 202 AT Commands This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default).
Page 203 AT Commands &P0 Selects 39% - 61% make/break ratio at 10 pulses per second. &P1 Selects 33% - 67% make/break ratio at 10 pulses per second. &P2 Selects 33% - 67% make/break ratio at 20 pulses per second. Result Codes: n = 0, 1, 2 Otherwise ERROR...
Page 204 AT Commands This command displays the current configuration of the modem. If nonvolatile memory is supported the stored profiles are displayed as well. &V View profiles. Saves the current (active) configuration (profile), including S-Registers. The current configuration comprises a list of storable parameters illustrated in the &V command.
Page 205 AT Commands This command determines the type of error control used by the modem when sending or receiving data. Buffer mode. No error control. Direct mode. MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects.
Page 206 AT Commands Disable flow control. XON/XOFF software flow control. CTS/RTS to DTE (default). Result Codes: n = 0, 1, 3 Otherwise ERROR Disable protocol result code appended to DCE speed. Enable protocol result code appended to DCE speed (default). Result Codes: n = 0, 1 Otherwise ERROR...
Page 207 AT Commands This command determines the operation of V.42bis and MNP class 5 data compression. On-line changes do not take effect until a disconnect occurs first. V.42bis/MNP 5 disabled. No data compression. V.42bis/MNP 5 enabled. Data compression enabled (default). Result Codes: n = 0, 3 Otherwise ERROR...
Page 208 S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination.
Page 209 S-registers This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default:...
Page 210 S-registers This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII This register sets the character recognized as a backspace and pertains to asynchronous only.
Page 211 S-registers This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction.
Page 212 S-registers S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9...
Page 213 S-registers The following table shows the result codes. Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone ERROR Invalid command...
Page 214 S-registers Result Code Numeric Description CONNECT 28800 EC* Connection at 28800 bps CONNECT 31200 EC* Connection at 31200 bps CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full : EC only appears when the Extended Result Codes configuration...
Page 215 ■ Expand the capabilities of your Wireless LAN Access Points, to support Wireless devices that have been equipped with Wireless LAN card. The internal Wireless LAN card can’t be used with the TOSHIBA Wireless LAN PC card. W‡s†k‡ÂIi‚‰i€Â F!Â User’s Manual...
Page 216 Yw†s€s‡‡ÂH7PÂ The peer-to-peer workgroup configuration enables you to quickly set up a small Wireless workgroup, where the workgroup participants can exchange files using features such as Files and Printer Sharing as supported by Microsoft Networking. Peer-to-peer Wireless workgroup You can use this option to set up a temporary or ad-hoc network in environment where no access points are available, for example in Small Office/Home Office (SOHO) environments.
Page 217 Â Yw†s€s‡‡ÂH7PÂ ETWORK Stand-alone Wireless LAN With the Wireless LAN Access Points you can connect to a corporate Local Area Network (LAN) infrastructure to have Wireless access to all network facilities. LAN Infrastructures may either be. ■ Stand-alone Wireless LANs as pictured in the figure below. User’s Manual...
Page 218 Yw†s€s‡‡ÂH7PÂ ■ Wireless network infrastructures connected to an existing Ethernet network as pictured in the figure below. ETWORK LAN Infrastructure The Wireless LAN card functions like any standard wired Ethernet card except it gives you the freedom of Wireless connections. Where an Ethernet card requires a cable connection to a hub and/or patch panel, the cable physically limits the location of the wired connection.
Page 219 Â Yw†s€s‡‡ÂH7PÂ The TOSHIBA Wireless LAN mini-PCI card is a Wireless network card that fits into a mini-PCI Type IIIA slot. The Wireless LAN card is a Wireless network card that complies with the IEEE 802.11 standard on Wireless LANs (Revision B). The Wireless LAN card supports data rates up to 11 Mbit/s.
Page 220 Yw†s€s‡‡ÂH7PÂ Table: Physical specifications Form Factor Mini-PCI TypeIIIA Dimensions Weight Temperature and Humidity Operation 0 to 55 C Maximum humidity 95% Transit -20 to 70 C 15 to 95% (no condensation) Storage -10 to 60 C 10 to 90% (no condensation) Although the card may still operate in the range of –20 to 70 C, operation outside the range of 0 to 55 C may no longer be according to specifications.
Page 221 Â Yw†s€s‡‡ÂH7PÂ Table: Networking Characteristics ■ IEEE 802.11 Standard for Wireless LANS (DSSS) Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA) ■ Microsoft Windows® Networking Network Operating System Microsoft Windows® XP Host Operating System ■ NDIS5.1 Miniport Driver Media Access CSMA/CA (Collision Avoidance) with...
Page 222 Yw†s€s‡‡ÂH7PÂ Radio characteristics of Wireless LAN cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN networking products have been designed for operation in the license-free 2.4 GHz band, local radio regulations may impose limitations on the use of Wireless communication equipment.
Page 223 The range values listed in Table Radio characteristics are typical distances as measured at the TOSHIBA Wireless LAN laboratories. These values provide rule-of-thumb guides. They may vary according to the actual radio conditions at the location where the Wireless LAN product is installed.
Page 224 Wireless LAN card may support a different set of 2.4 GHz channels (see Table below). Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region. Table: Wireless IEEE 802.11 Channels Sets Frequency Range 2400-2483.5 MHz...
Page 225 Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference. alternating current ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CMOS: complementary metal-oxide semiconductor CPU:...
Page 226 Glossary LED: light emitting diode LSI: large scale integration MDA: monochrome display adaptor MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC:...
Page 227 Glossary adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer. This terms also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices.
Page 228 Glossary binary: The base two number system composed of zeros and ones (off or on), used by most digital computers. The right most digit of a binary number has a value of 1, the next a value of 2, then 4, 8, 16, and so on.
Page 229 Glossary chip: A small semiconductor containing computer logic and circuitry for processing, memory, input/output functions and controlling other chips. CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit fabricated on a silicon wafer that requires very little power. Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable.
Page 230 Glossary data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve.
Page 231 Glossary erase: See delete. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. escape: 1) A code ( ASCII code 27), signalling the computer that what follows are commands;...
Page 232 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. I/O devices: Equipment used to communicate with the computer and transfer data to and from it.
Page 233 Glossary interrupt request: A signal that gives a component access to the processor. jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power.
Page 234 Glossary megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions.
Page 235 Glossary OCR wand: A device that reads, using an optical device, hand written or machine printed symbols into a computer. See also OCR. OCR: Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device.
Page 236 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. RAMDRIVE: Part of the computer’s random access memory assigned to simulate a disk.
Page 237 TFT: A colour LCD technology that applies individual transistors to each pixel enabling fine display control and excellent screen legibility. TOSHIBA Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions. Touch pad: A pointing device integrated into the TOSHIBA computer palm rest.
Page 238 Glossary Warm dock/undock: Connecting or disconnecting a device to or from the computer while the computer is suspended. warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application or document.
Page 239: Cleaning The Computer
Bluetooth wireless connecting 4-13 technology 4-16 disconnecting 4-14 Built-in Modem Abbreviations xxiii Cache memory About TOSHIBA Wireless CPU cache solution level 2 cache AC adaptor Changing to the laptop connecting mode 4-12 AC adaptor 1-4, 2-13 Changing to the Tablet...
Page 240: F1 ... F12 Function Keys
Index Icons xxiii Emulating keys on Indicators 2-11 enhanced keyboard Infrared port Enterprise networking Installing a Compact Environmental Flash module Requirements Installing memory Equipment checklist module in Slot B 8-13 Equipment setup Installing the tablet pen computer placement Instant security general conditions Ergonomics lighting...
Page 241 Index Problems AC power Opening the display analysing symptoms Operating Basics battery Operating System Bluetooth 9-16 Optional Devices diskette drive hard disk drive hardware and system Panel power off 6-19 checklist Password identifying cause power on infrared port problems initial precautions starting the keyboard computer with...
Page 242: Using The Optional Usb Fdd Kit
Index TOSHIBA TOSHIBA Console 1-11 Safety precautions TOSHIBA tablet pen SD card TOSHIBA Tablet pen 1-12 SD cards Toshiba Utilities installing Touch pad removing Troubleshooting Security lock 1-12, 8-18 Turning on the overlays Self test Typewriter keys Setting up Single tap...

Toshiba Portege 3500 User Manual

Chapter 7 HW Setup and Passwords

Preface

Chapter 1 Introduction

Chapter 2 The Grand Tour

Chapter 3 Getting Started

Chapter 4 Operating Basics

Chapter 5 The Keyboard

Chapter 6 Power and Power-Up Modes

Chapter 8 Optional Devices

Chapter 9 Troubleshooting

Appendix A Specifications

Quick Links

Related Manuals for Toshiba Portege 3500

Summary of Contents for Toshiba Portege 3500

Table of Contents