Page 1
FILE NO. 810-200314 SERVICE MANUAL DIGITAL VIDEO HDD/DVD VIDEO RECORDER RD-XS30SB May, 2003...
Page 2
LASER BEAM CAUTION LABEL When the power supply is being turned on, you may not remove this laser beam caution label. If it removes, radiation of a laser may be received. PREPARATION OF SERVICING Pickup Head consists of a laser diode that is very susceptible to external static electricity. Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement, its life might be shortened.
CONTENTS SECTION 1 GENERAL DESCRIPTIONS 2. LOCATION OF MAIN PARTS 1. OPERATING INSTRUCTIONS 2-1. Location of Main Parts Specifications 2-2. Location of PC Boards SECTION 2 PART REPLACEMENT AND ADJUSTMENT PROCEDURES 1. REPLACEMENT OF MECHANICAL PARTS 1-2. PC Board Replacement 1-2-1.
SECTION 1 GENERAL DESCRIPTIONS 1. OPERATING INSTRUCTIONS Please refer to the owner's manual about the contents.
Page 5
2. LOCATION OF MAIN PARTS 2-1. Location of Main Parts HDD1 HDD UNIT RAM1 RAM DRIVE FAN1 FAN Fig. 1-2-1 2-2. Location of PC Boards EU01 Digital PC board EU05 Mother board EU02 Power PC board EU03 Front PC board EU55 Jack PC board Fig.
SECTION 2 PART REPLACEMENT AND ADJUSTMENT PROCEDURES CAUTIONS BEFORE STARTING PART REPLACEMENT Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to ground as required. Many screws are used inside the unit. To prevent the screws from missing or dropping, etc. always use a magnetized screwdriver in servicing.
1-1-3. Front Panel 1-1-5. Operation Panel Door 1. Remove the top cover. (Refer to item 1-1-1.) 1. Open the operation panel door (1). 2. Remove the HDD. (Refer to item 1-1-2.) 2. Release two claws and unhinge the door (1). 3.
1-1-6. RAM Drive 1-1-7. Fan 1. Remove the front panel. (Refer to item 1-1-3.) 1. Remove a connector (1), two screws (2) and the fan (3). 2. Loosen the binding band (1) and disconnect a connec- Fan (3) tor (2). 3.
Page 9
1-2-2. Mother PC Board 1-2. PC Board Replacement 1. Remove the HDD. (Refer to item 1-1-2.) 1-2-1. Digital PC Board 2. Remove the front panel. (Refer to item 1-1-3.) 1. Remove the HDD. (Refer to 1-1-2.) 3. Remove the RAM drive. (Refer to item 1-1-6.) 2.
Page 10
1-2-3. Power PC Board 1-2-4. Front and Jack PC Board 1. Remove the front panel. (Refer to item 1-1-3.) Cautions : 2. Remove seven screws (1), then remove the stay (2). • Danger of explosion if battery is incorrectly replaced. 3.
SECTION 3 SERVICING DIAGRAMS 1. CIRCUIT SYMBOLS AND SUPPLEMENTARY EXPLANATION 1-1. Precautions for Part Replacement • In the schematic diagram, parts marked (ex. • Using the parts other than those specified shall violate the regulations, and may cause troubles such as F801) are critical part to meet the safety regulations, operation failures, fire etc.
SECTION 4 PARTS LIST SAFETY PRECAUTION The parts identified by ! ( ) mark are critical for safety. Replace only with part number specified. The mounting position of replacement is to be identical with originals. The substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create shock, fire or other hazards.
Page 53
SPECIFICATIONS Power requirement during operation Power requirement at standby 3.7W or below (Eco mode: off) 2.3W or below (Eco mode: on) Power supply 230-240V AC, 50/60 Hz Mass 5.4kg External dimension Width 430 x Height 78 x Depth 350mm Incoming channels TV : 2-69CH, CATV : 1-125CH Antenna input/output terminal VHF/UHF : 759, F Connector...