Table of Contents
Advertisement
Introduction
Identification of controls (Continued)
The instructions in this manual describe the functions on the remote control. See the page in
Remote control
VCR DVD button
22
EJECT button (VCR)
29
CLOCK/COUNTER button 33
VCR MENU button
23
SETUP button 58
CM SKIP button
31
ZOOM button
45
TOP MENU button
49
Direction buttons
(
/ / /
)
45
SET+/- buttons
23
CH+/- buttons
34
CANCEL button 26
CLEAR button
45
STOP button
30 42
PAUSE/STEP button 31
43
INDEX- button
33
SKIP
button
44
REV button 30
44
REC/OTR button 34 36
TIMER REC button 37
Direct channel
28
Selection buttons (0-9)
Number buttons (0-9)
45
COUNTER RESET button
32
ANGLE button 49
ATR button
31
SUBTITLE button 51
DVD MENU button
Use the DVD MENU button to display the menu
included on many DVD video discs. To operate a menu,
follow the instructions in "DVD Menu."
49
12
Connections
Antenna connections
If you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead to page
the proper connections.
Antenna to DVD/VCR connection
The DVD/VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TV and
connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna
system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.
1
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
75 ohm Coaxial Cable
2
Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
Matching Transformer 300 ohm Input 75
ohm output (not supplied)
300 ohm Twin Lead (Flat) Wire
(not supplied)
3
Separate VHF and UHF Antennas
Combiner 75/300 ohm Inputs 75 ohm output
UHF
VHF
300 ohm Twin Lead (Flat) Wire
(not supplied)
75 ohm Coaxial Cable
Note:
If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and
one 75 ohm output.
Notes:
•
A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to
the DVD/VCR properly.
•
For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type
antenna is required.
•
If you are not sure about the connection, please refer to qualified service personnel.
14
for details.
POWER button
22
OPEN/CLOSE button (DVD) 42
TV/VCR button 22
INPUT SELECT button
40
SLOW button
31
44
49
DVD MENU button
ENTER button
23 58
RETURN button
58
PLAY button 30
42
INDEX+ button
33
button
SKIP
44
FWD button
30
44
A-B RPT button 47
SP/SLP button 34
PLAY MODE button 47
CALL button 11
DISPLAY button 11
ZERO RETURN button
32
JUMP button
45
MARKER button
46
AUDIO SELECT button 39
AUDIO button
50
16
for
DVD/VCR
DVD/VCR
DVD/VCR
(not supplied)
Inserting batteries
1
Open the battery compart-
2
Install two "AAA" batteries
ment cover in the direction of
(supplied), paying attention to the
the arrow.
polarity diagram in the battery
compartment.
Caution:
Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with
applicable laws and regulations.
• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
• Always remove batteries from remote control if they are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from leaking into the battery compartment.
Remote control basics
• Press POWER to turn the DVD/VCR on or off.
• Select your desired operating mode (DVD or VCR) using VCR DVD.
(DVD or VCR indicator on the front panel will show you which mode is selected.)
• Press CH + or CH – to move through the channels one channel at a time.
• The
/
/ /
are also used to navigate on-screen menu system.
• You can directly access specific channels using Direct channel selection buttons (0–9).
• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the
DVD screen (DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons to
operate.
• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of approx. 7 meters.
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the
connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
VHF/UHF IN
75 ohm Coaxial Cable (supplied)
Splitter 75 ohm Input
UHF
75/300 ohm outputs
75 ohm Coaxial Cable
(not supplied)
VHF
(supplied)
UHF
Splitter 75 ohm Input
300 ohm outputs
(not supplied)
75 ohm Coaxial Cable
VHF
(supplied)
3
Replace the compartment
cover.
Approx. 7 meters
13
TV
Note:
If a VHF or UHF antenna is used,
set the TV/CABLE menu option to
the "TV" mode.
TV with single 75 ohm VHF/UHF antenna
input
TV
Note:
If a VHF or UHF antenna is used,
set the TV/CABLE menu option
to the "TV" mode.
TV with 300 ohm UHF and 75 ohm VHF
antenna inputs
TV
Note:
If a VHF or UHF antenna is used,
set the TV/CABLE menu option to
the "TV" mode.
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
15
Advertisement
Chapters
Table of Contents
Troubleshooting
