Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
protection
instruction
manual
1. SAFETY
Familiarise yourself with the application and limitations, as well as the potential hazards of the spray gun.
9
WARNING! Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
ˆ
Maintain the spray gun in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Locate the spray gun in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is
9
adequate ventilation and lighting.
Keep the spray gun clean for best and safest performance.
9
Ensure the air system has sufficient output for the spray gun air consumption (see specification).
9
Wear approved respiratory protection, safety eye goggles and skin protection.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
When gun is not in use ensure the air supply is disconnected.
9
Avoid unintentional operation.
9
DO NOT paint were there is any source, or possible source, of ignition as paint mist is extremely flammable.
8
DO NOT point spray gun at yourself or at other persons or animals.
8
DO NOT carry the spray gun by the air hose, or yank the hose from the air supply.
8
DO NOT use the spray gun for any purpose other than for which it is designed.
8
DO NOT allow untrained persons to operate the spray gun.
8
DO NOT get the spray gun wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT operate gun if any parts are missing or damaged as this may cause failure and/or personal injury.
8
DO NOT direct air from the air hose at yourself or others.
8
2. INTRODUCTION
Gravity feed spray gun designed for applying clear finishing coats. Air cap engineered to deliver high mist pressure for rapid paint application
and extended working distance. Stainless steel air and laquer flow channels provides long life. Features air and laquer flow controls for fine
adjustment of spray pattern.
3. SPECIFICATIONS
Model no: ..................................................................... HP01
Standard set up: .......................................................... 1.3mm
Air pressure: ............................................................. 29-32psi
Air consumption: ....................................................... 10.1cfm
Pot capacity: ................................................................ 600ml
© Jack Sealey Limited
INSTRUCTIONS FOR
GRAVITY SPRAY GUN 1.3MM SET-UP
FINISHING COAT
HP01
MODEL NO:
Wear
respiratory
protection
Original Language Version
HP01 Issue No:1 04/11/15
Advertisement
Summary of Contents for Sealey HP01
- Page 1 HP01 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Vibration may cause failure if a quick change coupling is connected directly to the spray gun. To overcome this, connect a leader hose to the spray gun (Sealey ref: AH2R or AH2R/38). A quick change coupling may then be used to connect the leader hose to the air line recoil hose.
- Page 3 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500. Environmental Protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.