Advertisement
Quick Links
i
Helpful Hints
1
2
What the LEDs mean
Restarting Wi-Fi setup mode
Red = Power
The iQ20 will start Wi-Fi setup mode when
Yellow - Slow Flashing = Searching for
the WIRED / WI-FI switch is set to Wi-Fi and
Network
its memory has been cleared. To clear the
Yellow - Solid = Connected to Network
memory, toggle the switch and leave it in the
LEDs may flicker—this is normal.
Wi-Fi position.
Green = Connected to Internet
My Network
Neighbors Network
4
3
Neighbor #2
Evaluating Wi-Fi signal strength For best reception
(Wi-Fi installs only)
Signal strength depends on your router and
A. Always install the iQ20 web-connect
the mounting location of the iQ20 web-connect
device with the antenna on the right side,
device. Use the Hotspot method to evaluate
toward the sky and within arms reach.
(See Section 3.1). If you move the router closer
and signal still not strong, consider installing
B. Install at least 10' (3m) from any high
a Wi-Fi range extender, Wi-Fi repeater, or
voltage electric motors and 5' (1.5m) away
another type of router. You may also install an
from other transceivers.
app on your smart phone (e.g., Wi-Fi Analyzer
C. Install as close to the home network
or Wi-Fi Sweetspots) to check your signal
router as possible.
strength and bandwidth.
5
6
When and how to use a 6584
WPS Helpful Hints
multiplex board
• Some brands use other names (like Quick Setup)
or other icons (such as padlock or similar) for WPS.
A maximum of two (2) RS485 cables can be connected
• Some routers may have WPS disabled, which
per RS485 connector. To connect additional RS485
may require using the hotspot method (4A]
• The hotspot method (4A) is recommended for
devices, a Multiplex Board may be required.
Apple
®
routers
Installation instructions included with part # 6584
i
This Quick Start Guide is to help you quickly install
your system. Be sure to read all WARNINGS in the
complete installation manual.
WARNING
To prevent risk of electrical shock which can result in severe injury or death,
ENSURE that the AquaLink
system is OFF before proceeding with installation.
®
FOR YOUR SAFETY
This product must be installed and serviced by a contractor who is licensed and
qualified in pool equipment by the jurisdiction in which the product will be installed where such state or
local requirements exist, the maintainer must be a professional with sufficient experience in pool equipment
installation and maintenance so that all of the instructions in this manual can be followed exactly. Before
installing this product, read and follow all warning notices and instructions that accompany this product.
Failure to follow warning notices and instructions may result in property damage, personal injury, or death.
Improper installation and/or operation will void the warranty. Improper installation and/or operation can create
unwanted electrical hazard which can cause serious injury, property damage, or death. Turn off power at the
main circuit feeding the AquaLink power center to disconnect the power center from the system.
Installation manual (H0433500) and Owner's manual (H0433600)
are available online at www.iAquaLink.com or by calling:
USA: 1-800-822-7933 | CANADA: 1-888-647-4004 |
AUSTRALIA: 1800-688-552
How It Works
INTERNET
Your
iQ20 Web
Power Center
Internet
Connect
Router
Device
Zodiac Pool Systems LLC
Zodiac Pool Systems Canada, Inc.
2882 Whiptail Loop # 100, Carlsbad CA 92081
2-3365 Mainway, Burlington, ON L7M 1A6
1.800.822.7933 | www.Jandy.com
1-888-647-4004 | www.ZodiacPoolSystems.ca
ZODIAC ® is a registered trademark of Zodiac International, S.A.S.U., used under license.
All other trademarks referenced herein are the property of their respective owners.
©2019 Zodiac Pool Systems LLC
Quick Start Guide
Pool System
H0637900_REVA
iQ20 Web-
Connect Device
Advertisement
Related Manuals for Jandy iQ20
Summary of Contents for Jandy iQ20
- Page 1 Turn off power at the Red = Power The iQ20 will start Wi-Fi setup mode when main circuit feeding the AquaLink power center to disconnect the power center from the system.
- Page 2 For security reasons, you must be connected to the same network the top-right corner after selecting your system from the “My Systems” screen. password to use the iAquaLink app or web interface. as the iQ20 web-connect device to add it to your account.