Table Of Contents - Sony MDX-65 Service Manual
Hide thumbs
Also See for MDX-65:
- Operating instructions manual (50 pages) ,
- Service manual (38 pages) ,
- Operating instructions (4 pages)
Table of Contents
Advertisement
QQ
3 7 63 1515 0
SERVICE NOTE
CAUTION
Use of controls or adjustments or performance of proce-
dures other than those specified herein may result in haz-
ardous radiation exposure.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR
BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-up
block. Therefore, when checking the laser diode emission, observe
from more than 30 cm away from the objective lens.
NOTES ON PICK-UP FLEXIBLE BOARD
TE
L 13942296513
The pick-up flexible board in this set is secured to the optical pick-up
with an adhesive tape. Once the tape is removed, an adhering force
becomes weak, and it cannot be reused.
Therefore, if the optical pick-up is replaced, replace also the pick-up
flexible board with a new one.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
(KMS-241A/J2N)
The laser diode in the optical pick-up block may suffer electrostatic
break-down easily. When handling it, perform soldering bridge to
the laser-tap on the flexible board. Also perform measures against
electrostatic break-down sufficiently before the operation. The
flexible board is easily damaged and should be handled with care.
laser-tap
OPTICAL PICK-UP FLEXIBLE BOARD
www
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN
.
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
http://www.xiaoyu163.com
x
ao
u163
y
i
- 2 -
http://www.xiaoyu163.com
2 9
8
TABLE OF CONTENTS
1-1. To Place the Set into Playback Mode ................................. 3
1-2. How to Check the Servo Board Waveforms ...................... 3
Preparations ............................................................................ 4
Listening MDs ........................................................................ 4
Connections ............................................................................ 5
3-1. Panel (Rear) Assy ............................................................... 6
3-2. Case (Upper) ...................................................................... 6
3-3. Panel (Front) Assy .............................................................. 7
3-4. MD Block ........................................................................... 7
3-5. Main Board ........................................................................ 8
3-6. Chassis (OP) Block ............................................................ 8
3-7. Servo Board ........................................................................ 9
3-8. Optical Pick-up .................................................................. 9
3-9. Note on Assembly for the Chassis (OP) Block ................ 10
4-1. IC Pin Descriptions .......................................................... 11
4-2. Circuit Boards Location ................................................... 14
4-3. Block Diagram ................................................................. 15
4-4. Printed Wiring Boards -Servo Section- .......................... 17
4-5. Schematic Diagram -Servo Section- ............................... 21
4-6. Schematic Diagram -Main Section- ................................ 23
4-7. Printed Wiring Boards -Main Section- ........................... 26
Q Q
4-8. Printed Wiring Board -Power Section- ........................... 29
3
6 7
1 3
1 5
4-9. Schematic Diagram -Power Section- .............................. 31
5-1. Case Section ..................................................................... 38
5-2. Main Board Section ......................................................... 39
5-3. MD Section (1) ................................................................. 40
5-4. MD Section (2) ................................................................. 41
5-5. MD Section (3) ................................................................. 42
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
co
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
9 4
2 8
0 5
8
2 9
9 4
2 8
....................................... 43
m
9 9
9 9
Advertisement
Table of Contents
