Related Manuals for Sony SLV-EZ70AS/NZ
Summary of Contents for Sony SLV-EZ70AS/NZ
- Page 1 3-865-383-12 (1) Video Cassette Recorder Operating Instructions PAL NTSC SLV-EZ70AS/NZ ©1999 by Sony Corporation...
- Page 2 WARNING Caution Television programmes, films, video tapes and To prevent fire or shock hazard, do not expose other materials may be copyrighted. the unit to rain or moisture. Unauthorized recording of such material may To avoid electrical shock, do not open the be contrary to the provisions of the copyright cabinet.
-
Page 3: Table Of Contents
Table of contents Getting Started Step 1: Unpacking Step 2: Setting up the remote commander Step 3: Connecting the VCR 11 Step 4: Tuning your TV to the VCR 13 Step 5: Setting the clock 15 Step 6: Presetting channels with EASY G-CODE SET UP 17 Presetting channels 22 Setting up the G-CODE* system manually 25 Changing/disabling programme positions... -
Page 4: Getting Started
Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: • Remote commander • Aerial cable • R6 (size AA) batteries Checking your model name The instructions in this manual are for the 2 models : SLV-EZ70AS and SLV-EZ70NZ. -
Page 5: Step 2: Setting Up The Remote Commander
Using the remote commander Remote sensor You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the g... - Page 6 Call up on-screen display √/◊ Change the Teletext page Menu buttons Operate TV menu options WIDE Switch the wide mode of a Sony wide TV (For other manufacture’s wide TV, see “Controlling other TVs with the remote commander” on page 7) Getting Started...
- Page 7 Now you can use the ON/STANDBY, VOL +/–, PROG +/–, programme number buttons, ? (ten’s digit) and TV/VIDEO buttons to control your TV. You can also use the buttons marked with a dot (•) to control a Sony TV. To control the VCR, reset TV / VIDEO to VIDEO .
- Page 8 • If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander. • You may not be able to use some buttons to control non-Sony TVs due to the remote commander’s signal limitations.
-
Page 9: Step 3: Connecting The Vcr
Step 3 Connecting the VCR Connect the aerial to your VCR and TV as shown below to watch TV programmes and VCR pictures on your TV. In addition, if your TV has audio/video (A/V) input jacks, we recommend you connect the VCR to your TV using an audio/video cable to get a better picture and sound. - Page 10 SKY TV normal TV programmes using the DECODER G-CODE system, etc. VIDEO IN Video cable (not supplied) Note • You may not receive TV programmes depending on the types of decoders. In this case, contact your Sony dealer. Getting Started...
-
Page 11: Step 4: Tuning Your Tv To The Vcr
Step 4 Tuning your TV to the VCR If you have connected your VCR to the TV using the audio/video cable, skip this step. 1/u ON/STANDBY PROGRAM +/– RF CHANNEL ON/STANDBY Press 1/u ON/STANDBY to turn on the VCR. Press RF CHANNEL on the VCR. The factory-preset RF channel appears in the display window. - Page 12 If you cannot obtain a clear picture after performing this procedure, we recommend you connect the VCR and TV using an audio/video cable (see “To a TV that has audio/video input jacks” on page 9). If the same symptom persists, consult your nearest Sony dealer. Getting Started...
-
Page 13: Step 5: Setting The Clock
Step 5 Setting the clock ON/STANDBY You must set the time and date on the VCR to be able to use the timer recording features properly. Before you start… • Turn on your TV and set it to the video channel. MENU >/./?// •... - Page 14 Step 5: Setting the clock (continued) Press >/. to set the date. CLOCK SET The day of the week is set automatically. 2 . 1 . 1 9 9 9 MO 0 : 0 0 PLAY SELECT : [ OK ] Press / to flash the month and set the CLOCK SET month using >/..
-
Page 15: Step 6: Presetting Channels With Easy G-Code Set Up
Step 6 Presetting channels with EASY G-CODE SET MENU EASY G-CODE SET UP is a feature that simplifies the channel presetting and the G-CODE guide channel setting. Just choose your local area in the EASY >/. G-CODE SET UP menu, and the VCR will automatically preset the TV channels and the G-CODE guide channels for your area. - Page 16 Step 6: Presetting channels with EASY G-CODE SET UP (continued) Tips • If your area is not listed in the EASY G-CODE SET UP menu, set up the TV channels using the one touch tuning or the TUNER PRESET menu (see “Presetting channels” on page 17).
-
Page 17: Presetting Channels
Presetting channels If you can receive no channels or only a few channels after performing the EASY G-CODE SET UP (page 15), preset all receivable channels automatically using the one touch tuning or the TUNER PRESET menu. If some channels could not be preset automatically when using the EASY G-CODE SET UP, one touch tuning or TUNER PRESET menu, preset them manually;... - Page 18 Presetting channels (continued) Presetting all receivable channels automatically MENU Before you start… • Turn on the VCR and the TV. • Set the TV to the video channel. >/./?// MENU Press MENU, then press >/. to move the TUNER PRESET PROG 1 cursor (”) to TUNER PRESET and press NORMAL / CATV...
- Page 19 Presetting channels manually PROG +/– MENU >/./?// MENU Press MENU, then press >/. to move the TUNER PRESET PROG10 cursor (”) to TUNER PRESET and press NORMAL / CATV • NORM CATV AUTO PRESET CHANNEL SET • FINE TUNING PLAY SELECT Press >/./?// to move the cursor (”) TUNER PRESET...
- Page 20 Presetting channels (continued) • PROG Selected programme Press PROG +/– to select the programme position position. TUNER PRESET PROG14 NORMAL / CATV • NORM CATV AUTO PRESET CHANNEL SET • FINE TUNING SELECT Press / repeatedly until the channel you TUNER PRESET PROG14 want is displayed.
- Page 21 Disabling unwanted programme positions After tuning the TV channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. You can also disable unwanted programme positions using the SET UP CH AND G-CODE menu (page 27). In step 5 on page 20, press programme number button “0”...
-
Page 22: Setting Up The G-Code System Manually
Setting up the G-CODE system manually MENU The G-CODE system is a feature in Sony VCRs that simplifies programming the VCR to make timer recordings. First, we recommend that you set up the G-CODE guide channels for your area using the EASY G-CODE SET UP feature >/./?//... - Page 23 Press / twice to flash the guide channel SET UP CH AND G-CODE GUIDE PROG column. – – – – PLAY – – – – – – – – – – – – – – – – SELECT GUIDE CH CONFIRM Press >/.
- Page 24 Setting up the G-CODE system manually (continued) Setting up the G-CODE system for satellite broadcasts (if applicable) When your satellite tuner is connected via the AERIAL IN connector, first you have to set the programme position for each satellite channel using the TUNER PRESET menu.
-
Page 25: Changing/Disabling Programme Positions
Changing/ disabling programme positions MENU After setting the channels and G-CODE guide channels, you can change the programme positions as you like. If any programme positions are unused or contain unwanted channels, you can disable them. >/./?// Before you start… •... - Page 26 Changing/disabling programme positions (continued) Press >/. until the selected channel and SET UP CH AND G-CODE GUIDE PROG guide channel row moves to the desired – PLAY – programme position. – – The selected channel and guide channel – SELECT are inserted at the new programme SET GUIDE CH CONFIRM...
- Page 27 Disabling unwanted programme positions Note • Be sure to select the programme position you want to disable correctly. If you disable a programme position CLEAR by mistake, you need to reset that channel manually. MENU >/. MENU Press MENU, then press >/. to move the SET UP CH AND G-CODE GUIDE PROG...
- Page 28 Changing/disabling programme positions (continued) Press >/. to move the cursor (”) to the SET UP CH AND G-CODE PROG GUIDE row on which you want to disable. PLAY – – To display other pages for programme – – position 5 to 49 (SLV-EZ70AS) or 6 to 50 –...
-
Page 29: Basic Operations
Basic Operations Playing a tape 6 EJECT TRINITRON TV SYNCHRO PLAY COUNTER RESET DISPLAY P PAUSE · PLAY ) # FF p STOP ) FF 0 3 REW 0 REW § EJECT · PLAY COLOR SYSTEM p STOP Turn on your TV and set it to the video channel. Insert a tape. - Page 30 Playing a tape (continued) Press · PLAY. When the tape reaches the end, it will rewind automatically. PLAY Additional tasks Press Stop play p STOP Pause play P PAUSE Resume play after pause P PAUSE or · PLAY Fast-forward the tape ) # FF () FF on the VCR) during stop Rewind the tape 0 3 REW (0 REW on the VCR) during stop...
- Page 31 To use the time counter At the point on the tape that you want to find later, press COUNTER RESET. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter. To display the counter on the TV screen, press DISPLAY. Notes •...
- Page 32 Turning on the VCR and TV, and starting playback automatically (Trinitron TV Synchro Play) You can only use this function if your TV is made by Sony (Trinitron TV). How to connect to use this function Connect the VCR and TV with the audio/video cable (see “To a TV that has audio/video input jacks”...
-
Page 33: Recording Tv Programmes
Recording TV programmes DISPLAY r REC PROG +/– SP/LP (SP/EP) INPUT SELECT Turn on your TV and set it to the video channel. Insert a tape with its safety tab in place. • PROG Press PROG +/– to select the programme position you want to record. - Page 34 Recording TV programmes (continued) Press SP/LP (SP/EP) to select the tape speed, SP or LP. SP/LP (SP/EP) LP (Long Play) provides recording time twice as long as SP (Standard Play), however, SP produces better picture and audio quality. Press r REC to start recording. r REC The recording indicator lights up red in the display window.
- Page 35 To save a recording To prevent accidental erasure, break off the safety tab as illustrated. To record on a tape again, cover the tab hole with adhesive tape. Safety tab To record NTSC colour system programmes The SLV-EZ70AS can record NTSC signals from the LINE-1 IN, LINE-2 IN and LINE-3 IN (SAT IN) jacks, and the SLV-EZ70NZ from the LINE-1 IN and LINE-2 IN jacks.
-
Page 36: Recording Tv Programmes Using The Easy Timer
Recording TV programmes using the easy timer You can record one programme on the same day (within 24 hours) with the easy timer. If the VCR clock has not been set, you can set the clock before setting the timer recording. Setting the easy timer PROGRAM +/–... -
Page 37: The Easy Timer
EASY TIMER Set the recording stop time in the same way as in step 2, then press the EASY TIMER knob. A programme number flashes. Turn the EASY TIMER knob clockwise or counterclockwise to select EASY TIMER the programme you want to record. To select the tape speed, press SP/LP (SP/EP). -
Page 38: The Easy Timer
Recording TV programmes using the easy timer (continued) Setting or changing the easy clock When “–:– –” is displayed in the display window, the VCR clock has not been set. Programme You need to set the clock using the easy number clock before setting the timer. -
Page 39: The Easy Timer
EASY TIMER Press the EASY TIMER knob to confirm the clock setting. The VCR enters the timer recording setting mode. To continue the easy timer START setting, go to step 2 in “Setting the easy timer” on page 36. To quit the easy timer setting mode without changing any settings, press the EASY TIMER knob repeatedly until the indicator appears in the display window. -
Page 40: The Easy Timer
Recording TV programmes using the easy timer (continued) To stop recording To stop the VCR while recording, press p STOP. To check or change the timer setting Press EASY TIMER knob repeatedly until the setting you want to check or change flashes. -
Page 41: Recording Tv Programmes Using The G-Code System
Recording TV programmes ON/STANDBY using the G-CODE CLEAR system G-CODE Just enter the G-CODE number, listed in the TV programme guide, for the Programme programme you want to record. The number date, times and programme position of buttons that programme are set automatically. You can preset up to eight programmes at a time. - Page 42 Recording TV programmes using the G-CODE system (continued) Press the programme number buttons to G–CODE G–CODE G–CODE NO. SP / LP enter the G-CODE number for the [ 8 2 4 7 7 6 9 1 – ] [ SP ] programme you want to record.
- Page 43 To stop recording To stop the VCR while recording, press p STOP. To record satellite broadcasts When you connect the satellite tuner and the VCR, you can record satellite programmes using the G-CODE number if applicable. Turn on the satellite tuner. On the satellite tuner, select the satellite programme for which you wish to make a timer setting.
-
Page 44: Setting The Timer Manually
Setting the timer manually ON/STANDBY You can preset up to eight programmes at a time. Before you start… • Check that the VCR clock is set to the correct time. • Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time. - Page 45 To record from a source connected to the LINE-1 IN or LINE-2 IN (or LINE-3 IN: SLV-EZ70AS only) jacks, press INPUT SELECT or PROG +/– to display “L1” or “L2” (or “L3”: SLV-EZ70AS only) in the “PROG” position. Press / to confirm the setting. The cursor (”) appears at the beginning of the line.
-
Page 46: Additional Operations
Additional Operations Playing/searching at various speeds ×2 ) FF & SLOW · PLAY 0 REW · PLAY ) # FF 0 3 REW CLICK SHUTTLE ring Playback options Operation View the picture during fast- During fast-forward, hold ) # FF () FF) down. During forward or rewind rewind, hold 0 3 REW (0 REW) down. - Page 47 Using the CLICK SHUTTLE ring on the VCR With the CLICK SHUTTLE ring, you can operate a variety of playback options. During playback or pause, turn the CLICK SHUTTLE ring clockwise or counterclockwise. Each change in the CLICK SHUTTLE ring position changes the playback mode, and the corresponding mark appears on the TV screen for a few seconds in the following way if the on-screen display function is on.
-
Page 48: Recording Tv Programmes Using The Quick Timer
Recording TV programmes using the quick timer After starting recording in the normal way, you can have the VCR stop recording automatically after a specified duration. QUICK TIMER While recording, press QUICK TIMER once. indicator appears in the display window. Press QUICK TIMER repeatedly to set the duration. -
Page 49: Synchronised Recording
Synchronised recording The Synchronised Recording feature enables you to record from the connected equipment such as a satellite tuner, or a cable TV decoder that has a timer function. Once you set the timer on the other equipment, the unit will start recording the programme synchronised with the timer. -
Page 50: Synchronised Recording
Synchronised recording (continued) Press SP/LP (SP/EP) to select the tape speed, (SP or LP for the PAL colour system, and SP or EP for the NTSC colour system.) Hold SYNCHRO REC down for more than two seconds. The SYNCHRO REC button lights up and the unit stands by for recording. -
Page 51: Checking/Changing/Cancelling Timer Settings
Checking/ changing/ ON/STANDBY cancelling timer settings CLEAR Before you start… • Turn on your TV and set it to the video channel. MENU >/./?// Press ON/STANDBY to turn on the VCR. Press MENU, then select TIMER SET/CHECK: • If you want to change a setting, go on to the 2 5 . - Page 52 Checking/changing/cancelling timer settings (continued) Press >/. to select the setting you want to change or cancel: • To change the setting, press ?// to flash the item you want to change, and press >/. to reset it. Then, press / repeatedly until the cursor (”) appears at the beginning of the line.
-
Page 53: Recording Stereo And Bilingual Programmes
Recording stereo and bilingual programmes In ZWEITON (German stereo) system This VCR automatically receives and records stereo and bilingual programmes based on the ZWEITON system. When a stereo or bilingual programme is received, the STEREO indicator appears in the display window. - Page 54 Recording stereo and bilingual programmes (continued) Selecting the sound during playback Press AUDIO MONITOR to select the sound you want. To listen to On-screen display Display window Stereo/main and sub STEREO STEREO (left and right channels) Left channel/main STEREO Right channel/sub STEREO Standard sound No indicator...
-
Page 55: Searching Using The Index Function
Searching using the index function INDEX The VCR marks the tape with an index SEARCH signal at the point where each recording begins. Use these signals as references to find a specific recording. The VCR can search up to 99 index signals ahead of or behind the current position. -
Page 56: Adjusting The Picture
Adjusting the picture Adjusting the tracking Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window, then goes off), distortion may occur if the tape was recorded in poor condition. If so, manually adjust the tracking. -
Page 57: Changing Menu Options
Changing menu options Press MENU, then select SET UP MENU. e.g. SLV-EZ70NZ SET UP MENU AUDIO MIX • HIFI AUDIO STD NICAM • • ON SELECT Press >/. to select the option to change, then press ?// to change the setting. Press OK to return to the original screen. -
Page 58: Editing
Editing Connecting to a VCR or stereo system How to connect to record on this VCR This VCR (Recorder) LINE-2 IN Other VCR (Player) LINE OUT VMC-810HG audio/video cable (not supplied) : Signal flow How to connect to a stereo system Connect LINE-1 IN or LINE-2 IN (or LINE-3 IN: SLV-EZ70AS only) AUDIO on this VCR to the audio output jacks on the stereo system, using the RK- C510KS audio cable (not supplied). -
Page 59: Basic Editing
Basic editing (when recording on this VCR) Before you start editing r REC • Turn on your TV and set it to the video channel. • Press INPUT SELECT or PROG +/– to display “L1” or “L2” (or “L3”: SLV-EZ70AS only) in the display window. -
Page 60: Audio Dubbing
Audio dubbing This feature lets you record over the normal audio track. The monaural COUNTER RESET sound previously recorded is placed while the original hi-fi sound remains unchanged. Use this feature to add AUDIO DUB commentary to a tape that you have recorded with a camcorder. -
Page 61: Additional Information
E-25CLDR video head cleaning cassette. If these cleaning cassettes are not available in your area, have the heads cleaned at your nearest Sony service facility (a standard service charge will be required). Do not use a commercially available liquid type cleaning cassette other than Sony’s, as they may damage the video... - Page 62 Troubleshooting (continued) Symptom Remedy No TV programmes • Make sure the TV is set to the video channel. If you are appear on the TV screen. using a monitor, set it to video input. TV reception is poor. • Adjust the TV aerial. The tape starts playing as soon •...
- Page 63 Symptoms caused by contaminated video heads • Normal picture • Rough picture • Unclear picture • No picture (or black & white screen appears) initial terminal contamination Sapphire tape cleaner The unit incorporates a sapphire tape cleaner which cleans a video tape when it is loaded.
-
Page 64: Specifications
Specifications System SKY TV DECODER (SLV-EZ70NZ only) VIDEO IN, phono jack (1) Channel coverage Input signal: 1 Vp-p, 75 ohms, unbalanced, SLV-EZ70AS: sync negative VIDEO OUT, phono jack (1) VHF AS0 to AS12, AS5A, AS9A Output signal: 1 Vp-p, 75 ohms, unbalanced, UHF AS28 to AS69 sync negative CATV S01 to S05, S1 to S41... -
Page 65: Index To Parts And Controls
Index to parts and controls Refer to the pages indicated in parentheses ( ) for details. Front panel !ª !• !¶ !§ !∞!¢ !£ !™ !¡ !º 1 1/u ON/STANDBY switch/ !™ EASY TIMER knob (36) indicator (11) !£ PROGRAM/TRACKING +/– 2 SYNCHRO REC button (49) buttons (56) 3 Tape compartment... - Page 66 Index to parts and controls (continued) Display window !º STEREO STOP CLOCK START NTSC N I C A M !£ !™ !¡ 1 Timer indicator (37, 39) 8 APC (Adaptive Picture Control) indicator (56) 2 (For SLV-EZ70NZ only) 9 Tracking indicator (56) NICAM indicator (53) 3 STEREO indicator (53) 0 Colour system indicator (30)
- Page 67 Rear panel (SLV-EZ70AS) Rear panel (SLV-EZ70NZ) 1 Mains lead (9) 4 LINE-2 OUT (AUDIO) AUDIO R/L jacks (10) 2 LINE-1 IN AUDIO R/L/VIDEO 5 AERIAL IN connector (9) jacks (58) 3 For SLV-EZ70AS: 6 AERIAL OUT connector (9) LINE-3 IN (SAT IN) AUDIO R/L/ 7 LINE-1 OUT AUDIO R/L/VIDEO VIDEO jacks (10) jacks (9)
- Page 68 Index to parts and controls (continued) Remote commander 1 TV / VIDEO remote control switch 2 6 EJECT button (30) 3 TRINITRON TV SYNCHRO PLAY button (32) 4 DISPLAY button (31, 34) 5 AUDIO DUB (dubbing) button (60) WIDE button (for TV) (8) 6 TV/VIDEO button (for TV) (6) 7 r REC (record) button (34) 8 EASY TIMER button (39)
-
Page 69: Index Search
!¢ ON/STANDBY switch (42, 45) !∞ AUDIO MONITOR button (53) !§ COUNTER RESET button (31) !¶ G-CODE button (41) !• CLEAR button (42, 52) !ª Programme number/? (ten’s digit) buttons (35, 39, 42) @º SET button (42) @¡ PROG (programme) +/– buttons (33) @™... -
Page 70: Index
Tracking adjustment 47, 56 automatically 18 Editing 58 Trinitron TV Synchro manually 19 EP mode 35 Play 32 one touch tuning 17 Tuning your TV to the using EASY G-CODE VCR 11 SET UP 15 ZWEITON broadcasts 53 Sony Corporation Printed in Malaysia...