Table of Contents
Advertisement
13-1-7(2). Noise Filter P.C. Board (MCC-1749) Replacement Procedure
Target model
43TN9877: MMY-MUP1201HT9*/1441HT9*/1681HT9*/096H1HT9*/120H1HT9*
Included items:
① MCC-1749 : 1pcs
Replacement Steps:
(1) Turn off the power supply of the outdoor unit and
wait at least 5 minutes for the capacitor to discharge.
(2) Remove all of the connectors and
tabs (CN04, CN14, CN15, CN29) attached to the
Noise Filter P.C. board. (Remove the connectors by
pulling the connector body. Do not pull the wire.)
(3) Remove screws (⑦：12pcs (M6) ) and Line-Filters
which were connected to the Noise Filter P.C. board.
(4) Remove fuse screws (⑧：4pcs (M6) ) and 2 fuses
which were connected to the Noise Filter P.C. board.
(If the fuse is not broken, reuse it.)
(5) Remove 8 screws(⑤：6pcs (M3), ⑥：2pcs (M4) ).
(6) Keep the removed screws as they will be reused.
(7) Remove the Noise Filter P.C. board from 6 spacers
(②:4pcs, ③:2pcs).
(8) If spacers (②, ③) are damaged, replace it and attach
bushes(④) to the service P.C. board(①).
(9) Screw the Noise Filter P.C. board by 8 screws
(⑤, ⑥) that were removed in step (5).
(10) Re-connect the fuses and screw terminals(⑧).
(11) Re-connect the connectors and screw
terminals(⑦), Line-Filters, solderless
terminal tabs (CN04, CN14, CN15, CN29).
Be sure that all the connectors and the
screw terminals are connected correctly
and securely inserted.
(12) If the components on the P.C. board were
bent during board replacement, adjust it
manually ensuring that it is not short or
contact other parts.
(13) Install the cover, then turn on the supply.
Check the operation.
The torque of the screws
⑤
Screw
⑥
Screw
Screw terminal
⑦
② Spacer : 4pcs
③ Spacer : 2pcs
solderless terminal
⑥ Screw(M4)
⑦ RED lead wire
Solderless
terminal
⑥ Screw (M4)
Solderless
terminal
Solderless
terminal
② Spacer
M3 x 0.7" (18mm)
0.44 ft•lbs (0.6 N•m )
M4 x 0.3" (8mm)
0.89 ft•lbs (1.2 N•m )
M6 x 0.47" (12mm)
2.21 ft•lbs (3.0 N•m)
④ Bush : 6pcs
Noise Filter P.C. board
(43TN9877)
⑦ BLACK lead wire
(CN28, M6)
⑧ Screw
② Spacer
(M6)
(CN26, M6)
⑧ Screw
(M6)
(CN29)
④ Bush
⑤ Screw (M3)
(CN15)
(CN14)
- 297 -
Push
Lock pin
2pcs
Line-filter are
another service parts.
that is not included.
How to remove a Line-filter
a) Remove the solderless terminal
tabs. (CN04, CN14, CN15, CN29)
b) Remove the screw terminals.
(CN01, CN02, CN03)
c) Remove the screws (CN11, CN12,
CN13), holding the lower Line-filter (L01).
d) Remove the screw (CN21, CN22, CN23),
holding the upper Line-filter(L02).
*L01 and L02 are same parts.
⑦ BLACK lead wire
(CN27, M6)
Fuse
④ Bush
⑤ Screw (M3)
② Spacer
⑦ RED lead wire
(CN21, M6)
⑦ WHITE lead wire
(CN22, M6)
⑦ BLACK lead wire
(CN23, M6)
③ Spacer
⑦ Line Filter(CN11, M6)
⑦ Line Filter(CN12, M6)
⑦ Line Filter(CN13, M6)
③ Spacer
⑦ RED lead wire
(CN01, M6)
⑦ WHITE lead wire
(CN02, M6)
⑦ BLACK lead wire
(CN03, M6)
② Spacer
Solderless
(CN04)
terminal
④ Bush
⑤ Screw (M3)
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
